Fuel Pressure Problem
使用本程序以诊断和排除燃油压力低故障,或者在下列任一事件代码激活时使用本程序。 有关事件代码和这些代码的默认触发点的信息,请参阅故障诊断与排除, "事件代码"。 必须进入 Caterpillar 电子技师(ET)的监控系统才能查看这些代码的当前触发点。
Show/hide table
诊断代码表     | ||
---|---|---|
说明     | 激活代码的条件     | 系统响应     |
E053-1 燃油压力低警告     | 燃油供应压力过低。     | 记录该代码。     |
94-1 燃油压力低警告     | 燃油供应压力过低。     | 记录该代码。 诊断灯将闪烁。 报警灯将发光。     |
可能原因
- 燃油油位低
- 燃油供应阀(如果配备)部分打开
- 燃油管
- 燃油中有空气
- 燃油箱堵塞
- 燃油滤清器
修理建议
燃油供给
- 目视检查燃油油位。 不可全信燃油表。 如有需要,加注燃油。 如果发动机用尽燃油,则需要排出燃油系统中的空气。 请参考操作和保养手册。
- 确保燃油供应阀(如有配备)处在完全打开位置。
- 检查燃油管路有无以下故障:阻塞, 皱缩管路, 挤压管路 和 松动连接。 如果发现燃油管路有故障,则应修理和/或更换管路。
- 如果进行以下任何步骤,则应充注燃油系统:
- 更换燃油滤清器
- 维护燃油低压供油回路
- 更换单体喷油器
注: 燃油低压供油管路上安装的观察孔将会有助于诊断燃油中的空气。 请参考系统操作/测试和调整。
- 更换燃油滤清器
- 检查燃油油箱有无可能会堵塞供油的外物。
- 检查燃油滤清器。
- 检查柴油是否受污染。 请参考系统操作/测试和调整。
- 低温天气会对燃油特性带来不利影响。 请参考操作和保养手册,了解有关改善低温操作中燃油特性的信息。
Caterpillar Information System:
G3500 Engines Nitrogen Oxide Sensor - Calibrate
C15 and C18 Petroleum Engines Engine Design
C15 and C18 Petroleum Engines Turbocharger Oil Lines
G3500B Engines Nitrogen Oxide Sensor - Calibrate
Manual Programming of a UPS System{4480, 7620} Manual Programming of a UPS System{4480, 7620}
Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620} Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620}
G3520C and G3520E Engines Turbocharger
Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803} Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803}
C15 and C18 Petroleum Engines Turbocharger Oil Lines
3608 Engine Valve Lifter - Assemble
2007/11/01 Replacement of the Combustion Head for the Aftertreatment Regeneration Device in On-highway Engines {1088, 1720, 1722}
C15 and C18 Petroleum Engines Turbocharger Oil Lines
3176C, 3406E and 3456 Industrial Engines Fuel Temperature Is High
3608 Engine Governor Drive - Assemble - Earlier
3176C, 3406E and 3456 Industrial Engines Intake Manifold Air Temperature Is High
3608 Engine Fuel Transfer Pump - Assemble
3176C, 3406E and 3456 Industrial Engines Oil Pressure Is Low
2007/12/03 Cylinder Head Gasket {1100, 1251}
3608 Engine Valve Lifter - Install
2008/12/08 Procedure for Cleaning the Power Train {3065, 3139}
3176C, 3406E and 3456 Industrial Engines Electrical Power Supply - Test
3608 Engine Air Starting Motor - Remove
3608 Engine Water Pump - Disassemble
3608 Engine Auxiliary Water Pump - Remove