Fuel Transfer Pump
Show/hide table
图 1 | g01423211 |
(1) 排气预留孔 |
Show/hide table
图 2 | g01423215 |
(2) 出口 |
Show/hide table
图 3 | g01423212 |
(3) 进口 (4) 压力调节阀 |
当燃油输油泵使用柴油时,燃油输油泵具有以下技术规格:
- 使泵在 2940 rpm 转速下运转。 整个旁通压力应为 716 到 786 kPa (104 到 114 psi)。
- 使泵在 2940 rpm 转速下运转。 在 550 kPa (80 psi) 压力下的流速必须为 3.0 L/min (0.8 US-Gall/min)。
- 使泵在 2940 rpm 运转。 在 650 kPa (94 psi) 压力下的流速必须为 4.5 L/min (1.19 US-Gall/min)。
- 使泵在120 rpm 转速下运转。 保持进口对空气打开 10 秒钟。 封闭进口。 泵必须能保持 30 kPa (4.5 psi) 的真空度最少 30 秒钟。
- 使泵在 2940 rpm 转速下运转。 保持进口对空气打开 10 秒钟。 封闭进口。 泵必须能保持 45 kPa (6.5 psi) 的真空度最少 30 秒钟。
- 封闭进口让泵在 120 rpm 转速下运转 30 秒钟。 泵的进口必须具备最小为 60.9 kPa (9 psi) 的吸入提升力。
从驱动端部观看泵时,泵的旋转方向为逆时针。
Show/hide table
图 4 | g01423216 |
(5) 组装之前,先将 155-0695 螺纹锁固胶 涂抹在螺柱的螺纹上。
(6) 螺母的扭矩 ... 30 ± 15 N·m (22 ± 11 lb ft)
Caterpillar Information System:
3516C Generator Set Engine Configuration Parameters
3516B Engine for 994F and 994H Wheel Loaders Electrical Connectors
3608 Engine Water Pump - Assemble
3608 Engine Engine Oil Pump - Install
3608 Engine Engine Oil Pump - Assemble
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Component Location
3608 Engine Engine Oil Pump - Disassemble
3516C Generator Set Engine System Overview
3608 Engine Valve Cover Base - Remove and Install
C12 Marine Engines Belts - Inspect/Adjust/Replace
14L Motor Grader Machine Systems Circle - Install
3608 Engine Engine Oil Filler and Oil Level Gauge - Remove and Install
3608 Engine Auxiliary Water Pump - Install
G3500 Generator Sets Battery or Battery Cable - Disconnect
3608 Engine Air Starting Motor - Disassemble
3608 Engine Air Starting Motor - Assemble
3608 Engine Air Starting Motor - Install
2007/11/05 Replacement of the Priming Pump {1258, 1263}
3608 Engine Barring Group - Remove and Install
Transmission, Torque Converter and Relief Valve Bench Test Procedures Reference Manual Contents {3030, 3101, 3133} Transmission, Torque Converter and Relief Valve Bench Test Procedures Reference Manual Contents {3030, 3101, 3133}
2008/04/14 A New Aftercooler is Now Used {1063}
Replace Exciter Rotor on LC6 Frame Generators{4457} Replace Exciter Rotor on LC6 Frame Generators{4457}
2007/10/22 Use Care During Disassembly of the Fuel Manifolds {1252, 1274}
2007/10/22 Use Care During Disassembly of the Fuel Manifolds {1252, 1274}