Finding Top Center Position for No. 1 Piston
Show/hide table
图 1 | g00569371 |
正时齿轮 (A) 喷油泵油泵驱动齿轮 (B) 惰轮 (C) 凸轮轴齿轮 (D) 曲轴齿轮 |
- 发动机正时齿轮的每个齿轮上均具有参考标记。 当这些标记对准后,1 号缸位于上止点位置。
注: 此发动机不通过销钉正时,而是采用具有奇数轮齿的惰轮。 如果拆下了喷油泵,不要转动发动机。 前壳体拆下后,必须利用正时标记对准齿轮。 用画笔标记轮齿。 通过啮合带有对应标记的轮齿重新安装喷油泵。
Show/hide table图 2 g01412325 喷油泵正时标记
(1) 正时标记
(2) 正时标记 - 喷油泵上的正时记号 (1) 和 (2) 指示泵与正时齿轮的相对位置。 标尺上的每个标记表示正时改变六度。
- 转动曲轴,直到 1 号活塞位于压缩冲程上的大约 60 度 BTC 为止。
注: 在 1 号气缸位于上止点位置的情况下检查气门间隙。 这样可确保气缸位于压缩冲程,而并非位于排气冲程上。
Show/hide table图 3 g00565561 曲轴皮带轮正时标记 - 曲轴皮带轮有一个标尺,范围是 0 至 40 度。 标尺上的每个刻度代表 5 度的曲轴转角。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
2007/09/01 Unauthorized Engine Modification {1000}
G3520B Industrial Engines CAN Data Link - Test
2007/11/01 The Remanufactured Control Group is Incorrect for the Application {1901, 7620}
2007/11/26 The Remanufactured Control Group is Incorrect for the Application {1901, 7620}
2007/09/10 A New Fuel Line and Hose Assembly are Used for the Fuel Cooler {1274}
C3.3 Industrial Engine Maintenance Interval Schedule
C3.3 Industrial Engine Fan Drive
Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100} Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290} The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
2007/09/01 An Improved Oil Level Gauge Is Now Used {1326}
2007/10/08 New ECM Software Is Available for Gas Compression Applications {7620}
14L Motor Grader Gear Pump (Transmission Charging and Scavenge) - Disassemble
C18 Power Module Before Starting Engine
G3408C and G3412C Engines Piston and Rings - Gallery Cooled Piston
14L Motor Grader Gear Pump (Transmission Charging and Scavenge) - Assemble
PM3500 Power Modules Overhaul Considerations
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Log File Messages
3500 Generator Sets Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
Copper Contamination of the Engine Oil in some 3500C Marine Engines{1000, 1348} Copper Contamination of the Engine Oil in some 3500C Marine Engines{1000, 1348}
3500 Generator Sets Emergency Stopping
G3408 and G3412 Engines Governor
C27 and C32 Generator Sets and C32 Power Module Return Fuel Lines{1274} C27 and C32 Generator Sets and C32 Power Module Return Fuel Lines{1274}
Remanufactured 3126 Cylinder Heads with Incorrect Valve Seats{1100} Remanufactured 3126 Cylinder Heads with Incorrect Valve Seats{1100}