Gear Pump (Transmission Charging and Scavenge) - Disassemble
Start By:
- Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Transmission Charging and Scavenge - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
- Remove O-ring seal (1) and O-ring seal (4). Remove bolts (2) and remove manifold assembly (3).
Show/hide table
Illustration 2 g01412736 - Remove O-ring seal (5) and O-ring seal (6) from manifold assembly (3).
Show/hide table
Illustration 3 g01412657 - Remove bolt (7). Remove cover assembly (8).
Show/hide table
Illustration 4 g01412697 - Remove O-ring seal (9) from cover assembly (8). Remove sleeve bearings (10) from cover assembly (8).
Show/hide table
Illustration 5 g01412784 - Remove gear (12) and remove shaft (11). Remove body (13).
Show/hide table
Illustration 6 g01412788 - Remove gears (14).
Show/hide table
Illustration 7 g01412794 - Remove key (15).
Show/hide table
Illustration 8 g01412797 - Remove gear assembly (16) and remove O-ring seal (17).
Show/hide table
Illustration 9 g01412811 - Remove sleeve bearings (18).
Show/hide table
Illustration 1 | g01412719 |
Caterpillar Information System:
C3.4 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C7 Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
2007/09/01 Unauthorized Engine Modification {1000}
G3520B Industrial Engines CAN Data Link - Test
2007/11/01 The Remanufactured Control Group is Incorrect for the Application {1901, 7620}
2007/11/26 The Remanufactured Control Group is Incorrect for the Application {1901, 7620}
2007/09/10 A New Fuel Line and Hose Assembly are Used for the Fuel Cooler {1274}
C3.3 Industrial Engine Maintenance Interval Schedule
C3.3 Industrial Engine Fan Drive
Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100} Correct Usage of the Oil Rail Plug for the Cylinder Head on C9 Engines{1100}
The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290} The Proper Procedures for Troubleshooting Mechanical Unit Injectors (MUI){1251, 1264, 1280, 1288, 1290}
2007/09/01 An Improved Oil Level Gauge Is Now Used {1326}
C18 Power Module Before Starting Engine
G3408C and G3412C Engines Piston and Rings - Gallery Cooled Piston
14L Motor Grader Gear Pump (Transmission Charging and Scavenge) - Assemble
PM3500 Power Modules Overhaul Considerations
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Log File Messages
3500 Generator Sets Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
Copper Contamination of the Engine Oil in some 3500C Marine Engines{1000, 1348} Copper Contamination of the Engine Oil in some 3500C Marine Engines{1000, 1348}
3500 Generator Sets Emergency Stopping
G3408 and G3412 Engines Governor
C27 and C32 Generator Sets and C32 Power Module Return Fuel Lines{1274} C27 and C32 Generator Sets and C32 Power Module Return Fuel Lines{1274}
Remanufactured 3126 Cylinder Heads with Incorrect Valve Seats{1100} Remanufactured 3126 Cylinder Heads with Incorrect Valve Seats{1100}
14L Motor Grader Machine Systems Blade Lift Arm - Remove