Prechamber - Clean/Inspect
注: 关于预燃室组件拆卸的注意事项贴膜位于各气门室盖的顶部。
Show/hide table
图 1 | g00902999 |
"为防止损坏,拆下预燃室前,先排放冷却液并拆下火花塞。 将燃烧传感器导线组件螺母拧紧至 9.5 ± .5 N·m (85 ± 5 lb in)。 请勿过度紧固。" |
Show/hide table
图 2 | g01302648 |
- 拆下点火体组件。 从点火体卸下预燃室杯 (1) 。 请参阅发动机拆解和组装手册的说明。
- 清除预燃室杯的沉积物。
- 检查密封法兰有无损坏和碎屑。 更换任何法兰有损坏的预燃室杯。 更换任何有腐蚀孔的预燃室杯。 更换任何有从孔向外延伸的裂纹的预燃室杯。
- 用 9U-5156 清洁工具总成 清洁气缸盖的预燃室密封垫组。 用干净的布和溶剂擦净表面。
- 安装新的预燃室密封垫和 O 形密封圈。
- 安装气缸盖的点火体组件。 请参阅发动机技术规范手册中关于正确拧紧的程序。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Starting - Test
G3520C and G3520E Generator Set Engines Speed/Timing - Test
C13 On-highway Engine Clean Gas Induction Valve
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Rear Seal - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Pump - Remove and Install
G3520C and G3520E Generator Set Engines Throttle Actuator - Test
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injector - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Filter Base - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Filter Base - Remove and Install - C0.5 and C0.7 Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Mechanical Fuel Transfer Pump
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Electrical Fuel Transfer Pump
G3520C and G3520E Generator Set Engines ECM - Replace
G3520C and G3520E Generator Set Engines Electrical Connectors - Inspect
G3520C and G3520E Generator Set Engines Control Module - Replace
C11 and C13 Engines and 14M and 16M Motor Graders Sensor Signal (Analog, Active) - Test
2006/11/27 An Updated Gasket for the Water Temperature Regulator Housing is Available {1355, 1380, 1393}
C13 On-highway Engine Exhaust Extension
G3600 Engines ECM Software - Install
C13 On-highway Engine Exhaust Extension
G3520C and G3520E Generator Set Engines Timing - Calibrate
G3520C and G3520E Generator Set Engines Generator Output Power Sensor - Set
G3520C and G3520E Generator Set Engines Speed Control (Switch) - Test
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission Does Not Automatically Shift Into Neutral