Crankshaft Front Seal - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7600 | 滑锤拉拔器 | 1 |
开始:
- 拆下曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用
4 mm (0.158 inch) 钻在曲轴前油封 (2) 上钻三个孔。Show/hide table注意 确保使用主唇部拆卸曲轴前油封。 不要损坏曲轴前油封壳体的边缘。
注: 拆卸曲轴前油封的过程中切勿损坏曲轴。
- 使用工具 (A) 小心拆下曲轴前油封 (2)。 将工具 (A) 的位置从一个孔换到另一个孔。 这样可使您均匀地从前壳体 (1) 上拆下曲轴前油封。
Show/hide table
图 1 | g01310976 |
典型示例 |
开始:
- 拆下曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
- 拆卸前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 还有另一个拆卸曲轴前油封的步骤。 从发动机上拆下前壳体后使用本步骤。
- 使用适当的心轴和压具从前盖上拆下油封。 确保前盖得到正确支撑,以防止在拆卸油封时损坏盖。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保前壳体 (1) 上的孔和曲轴的鼻端干净、无损坏。
- 用清洁的发动机机油润滑新曲轴前油封 (2) 的唇口。
- 将曲轴前油封 (2) 放置在前壳体 (1) 的孔中。
Show/hide table
注意 确保弹簧加载式曲轴前油封的唇缘朝向前壳体的内侧,并且正好位于曲轴前油封使用的壳体孔中。
- 使用适当的工具将曲轴前油封 (2) 安装到前壳体 (1) 上。
Show/hide table
图 2 | g01311777 |
典型示例 |
结束:
- 安装曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
Caterpillar Information System:
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Rear Seal - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Pump - Remove and Install
G3520C and G3520E Generator Set Engines Throttle Actuator - Test
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injector - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Filter Base - Remove and Install - C1.1, C1.5, C1.6 and C2.2 Engines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Filter Base - Remove and Install - C0.5 and C0.7 Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Mechanical Fuel Transfer Pump
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Electrical Fuel Transfer Pump
C11 and C13 Engines and 14M and 16M Motor Graders Injector Solenoid - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Glow Plugs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Engines with Flywheel Housing and Back Plate
C13 On-highway Engine Clean Gas Induction Valve
G3520C and G3520E Generator Set Engines Speed/Timing - Test
G3520C and G3520E Generator Set Engines Starting - Test
G3600 Engines Prechamber - Clean/Inspect
G3520C and G3520E Generator Set Engines ECM - Replace
G3520C and G3520E Generator Set Engines Electrical Connectors - Inspect
G3520C and G3520E Generator Set Engines Control Module - Replace
C11 and C13 Engines and 14M and 16M Motor Graders Sensor Signal (Analog, Active) - Test
2006/11/27 An Updated Gasket for the Water Temperature Regulator Housing is Available {1355, 1380, 1393}
C13 On-highway Engine Exhaust Extension
G3600 Engines ECM Software - Install
C13 On-highway Engine Exhaust Extension