Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 185-3630     | 带式扳手组件     | 1     |
开始:
- 连接转向机架锁。 请参阅拆解和组装, "转向机架锁 - 分离和连接"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 打开发动机罩。
- 拆下面板 (1) 。
Show/hide table
图 1 | g01153352 |
- 将杯 (2) 中的燃油排入合适的容器以便保存或处理。
Show/hide table
图 2 | g01154339 |
- 使用工具 (A) 拆下燃油粗滤器 (7) 。
Show/hide table
图 3 | g01154340 |
- 断开线束组件 (8) 和 (9) 。
- 断开软管组件 (3) 和 (6) 。
- 拆下螺栓 (5) 和燃油注油泵 (4) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 185-3630     | 带式扳手组件     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装燃油注油泵 (4) ,然后安装螺栓 (5) 。
Show/hide table
图 4 | g01154340 |
- 使用工具 (A) 安装燃油粗滤器 (7) 。
- 连接软管组件 (3) 和 (6) 。
- 连接线束组件 (8) 和 (9) 。
- 安装面板 (1) 。
Show/hide table
图 5 | g01153352 |
- 关闭发动机罩。
End By: 分离转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Install
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Remove
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Disassemble
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Install
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Remove
525C, 535C and 545C Wheel Skidders Grapple Pressure Sensor (Grapple Oil)
C27 and C32 Tier 4 Engines Flywheel
C7 Engines for Caterpillar Built Machines Crankshaft - Install
C7 Engines for Caterpillar Built Machines Crankshaft - Remove
525C, 535C and 545C Wheel Skidders Grapple Check Valve (Pilot)
966H and 972H Wheel Loaders Engine Supplement Engine Compartment Shield - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove
Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060} Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060}
3500B Series II Marine Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Assemble
2005/03/21 Correction to Testing and Adjusting , "Torque Converter Stall and Implement Pump Double Stall - Test" {3101, 5055, 5084}
3516B Off-Highway Trucks Factory Passwords Worksheet
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Remove
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Install
525C, 535C and 545C Wheel Skidders Grapple Grapple Frame
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Radiator Module - Install
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Hydraulic Tank
966H and 972H Wheel Loaders Machine Systems Bucket - Remove
966H and 972H Wheel Loaders Machine Systems Bucket - Install