Crankshaft - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 8T-5096     | 千分表总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
确保曲轴主轴承锁片与缸体和曲轴主轴承盖中的槽相互啮合。 |
- 清洁缸体上与主轴承配合的轴承表面。 将清洁的发动机机油涂抹在上主轴瓦上。 不要将清洁的发动机机油涂抹在轴承表面的背面。 将上主轴瓦安装在缸体中。 确保轴承背面的凸舌接合在缸体的凹槽中。
注: 6 号主轴承为止推轴承。
- 将清洁的发动机机油涂抹在曲轴轴承的轴颈上。 将合适的起吊设备连接到曲轴 (1) 。 曲轴 (1) 的重量约为 62 kg (137 lb)。 对准齿轮系上的识别标记。 将曲轴 (1) 安装在缸体中。
Show/hide table
图 1 | g01128041 |
- 清洁主轴承盖 (3) 的轴承表面。 将下主轴瓦安装在主轴承盖中。 确保轴承背面的凸舌接合在主轴承盖的凹槽中。 将清洁的发动机机油涂抹在下主轴瓦上。 不要将清洁的发动机机油涂抹在轴承表面的背面。
- 安装主轴承盖 (3) ,零件号朝向缸体右侧。 确保主轴承盖的编号为 1 到 7。 编号应从发动机前部开始。 将清洁的发动机机油或含钼润滑油涂抹到螺栓螺纹和垫圈上。
- 将螺栓 (2) 安装到主轴承盖 (3) 上。 用 54 ± 7 N·m (40 ± 5 lb ft) 的扭矩拧紧螺栓 (2) 。
注: 紧固后主轴承盖的螺栓时,尽可能远地朝前滑动主轴承盖,使盖与螺栓相抵。 将主轴承盖固定在位并拧紧螺栓。
- 将螺栓 (2) 再转动 90 ± 5度(1/4圈)。
- 用工具 (A) 检查曲轴 (1) 的端隙。 端隙必须在 0.07 mm 至 0.32 mm (0.003 in 至 0.013 in) 之间。
End By:
- 安装飞轮壳。 请参阅 拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装前壳体。 请参阅 拆解和组装, "壳体(前) - 安装"。
- 安装连杆轴承。 请参阅 拆解和组装, "连杆轴承 - 安装"。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Crankshaft - Remove
525C, 535C and 545C Wheel Skidders Grapple Check Valve (Pilot)
966H and 972H Wheel Loaders Engine Supplement Engine Compartment Shield - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Install
966H and 972H Wheel Loaders Engine Supplement Aftercooler Core - Remove and Install
C9 Engines for Caterpillar Built Machines Cylinder Block Cover - Remove and Install
AD30 Underground Articulated Truck Power Train Electronic Control General Information
AD55 Underground Articulated Truck Power Train Final Drive Spindle, Service and Parking Brake - Assemble
AD45B Underground Articulated Truck Power Train Electronic Control System Backup Alarm Always Off
AD30 Underground Articulated Truck Power Train Electronic Control Electronic Control Module (Power Train/Chassis)
AD45B Underground Articulated Truck Power Train Electronic Control System Backup Alarm Always On
C27 and C32 Tier 4 Engines Flywheel
525C, 535C and 545C Wheel Skidders Grapple Pressure Sensor (Grapple Oil)
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Remove
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Install
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Disassemble
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Remove
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Install
966H and 972H Wheel Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060} Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060}
3500B Series II Marine Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Assemble
2005/03/21 Correction to Testing and Adjusting , "Torque Converter Stall and Implement Pump Double Stall - Test" {3101, 5055, 5084}