Electric Starting Motor - Install
安装步骤
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上，从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏，则应使用新零件进行更换。
- 使用适当的起吊设备安置电动起动马达 (11) ，如图所示。 电动起动马达 (11) 的重量约为 27 kg (60 lb)。
Show/hide table
 | |
| 图 1 | g01154315 |
- 安装螺栓 (9) 和夹子 (10) 。
- 安装螺栓 (7) 和 (8) 。
Show/hide table
 | |
| 图 2 | g01154314 |
- 安装线束组件 (6) 。
Show/hide table
 | |
| 图 3 | g01154312 |
- 连接电缆组件 (4) 和 (5) 。
Show/hide table
 | |
| 图 4 | g01154311 |
- 安装盖 (3) 并连接电缆组件 (2) 。
Show/hide table
 | |
| 图 5 | g01154310 |
- 将蓄电池断路开关转到接通位置。
- 安装面板 (1) 。
Show/hide table
 | |
| 图 6 | g01154309 |
- 关闭发动机罩。
End By: 分离转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Remove
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Disassemble
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Install
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Remove
525C, 535C and 545C Wheel Skidders Grapple Pressure Sensor (Grapple Oil)
C27 and C32 Tier 4 Engines Flywheel
C7 Engines for Caterpillar Built Machines Crankshaft - Install
C7 Engines for Caterpillar Built Machines Crankshaft - Remove
525C, 535C and 545C Wheel Skidders Grapple Check Valve (Pilot)
966H and 972H Wheel Loaders Engine Supplement Engine Compartment Shield - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Install
966H and 972H Wheel Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060} Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060}
3500B Series II Marine Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Assemble
2005/03/21 Correction to Testing and Adjusting , "Torque Converter Stall and Implement Pump Double Stall - Test" {3101, 5055, 5084}
3516B Off-Highway Trucks Factory Passwords Worksheet
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Remove
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Install
525C, 535C and 545C Wheel Skidders Grapple Grapple Frame
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Radiator Module - Install
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Hydraulic Tank
966H and 972H Wheel Loaders Machine Systems Bucket - Remove