Piston Pump (Brake, Hydraulic Fan) - Install
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 定位活塞泵 (16) 并安装螺栓 (14) 和螺栓 (15) 。
Show/hide table
图 1 | g01154559 |
Show/hide table
图 2 | g01155754 |
- 把注油管 (13) 连接到缸体 (12) 上。
Show/hide table
图 3 | g01154558 |
- 定位支架 (11) 并安装螺栓 (10) 。
Show/hide table
图 4 | g01154557 |
- 连接软管组件 (8) 和 (9) 。
Show/hide table
图 5 | g01154556 |
- 连接软管组件 (7) 。
Show/hide table
图 6 | g01154555 |
- 定位支架 (6) 并安装螺栓 (5) 、螺栓 (4) 和垫片。
Show/hide table
图 7 | g01154554 |
- 连接软管组件 (2) 和 (3) 。
Show/hide table
图 8 | g01154553 |
- 安装面板 (1) 。
Show/hide table
图 9 | g01153352 |
- 为了对机具泵、转向泵、风扇泵的外壳注油,完全打开位于液压油箱和机具泵之间的注油阀。 请参看图 10。
Show/hide table
图 10 | g01873213 |
Show/hide table
图 11 | g01873215 |
Show/hide table
注意 |
---|
为避免损坏系统,请确保在起动前适当地给液压泵加注液压油。 |
- 把吹扫管路连接到位于风扇泵上方外壳回放管路内的测压口上。 请参看图 11。
- 开始为液压油箱加油。 一旦油开始流出吹扫管路,取下吹扫管路并完全关闭注油阀。
- 继续把液压油箱加注到正确的油位。 请参阅操作和保养手册, "液压系统机油 – 更换"。
注: 首次启动时,在液压系统已开始循环,液压油缸中的油位已调整到正确油位之前,发动机的运行不得超过低怠速。
End By: 分离转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Remove
3516B Off-Highway Trucks Factory Passwords Worksheet
2005/03/21 Correction to Testing and Adjusting , "Torque Converter Stall and Implement Pump Double Stall - Test" {3101, 5055, 5084}
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Assemble
3500B Series II Marine Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060} Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060}
966H and 972H Wheel Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Install
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Remove
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Disassemble
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Install
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Remove
525C, 535C and 545C Wheel Skidders Grapple Grapple Frame
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Radiator Module - Install
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Hydraulic Tank
966H and 972H Wheel Loaders Machine Systems Bucket - Remove
966H and 972H Wheel Loaders Machine Systems Bucket - Install
966H and 972H Wheel Loaders Machine Systems Tilt Cylinder - Remove and Install
966H and 972H Wheel Loaders Machine Systems Tilt Link - Remove
966H and 972H Wheel Loaders Machine Systems Tilt Link - Install
2005/04/18 Replacement of the Transmission Control Group for Earlier Models Is Updated {3065}
657G Wheel Tractor-Scraper Circuit Breakers - Reset
525C, 535C and 545C Wheel Skidders Hydraulic and Steering System Piston Pump (Implement, Steering, Brake)
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Water Pump - Remove and Install