Electric Starting Motor - Remove
拆卸步骤
开始:
- 连接转向机架锁。 请参阅拆解和组装, "转向机架锁 - 分离和连接"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 打开发动机罩。
- 拆下面板 (1) 。
Show/hide table
图 1 | g01154309 |
- 将蓄电池断路开关转到断开位置。
- 断开电缆组件 (2) 并拆下盖 (3) 。
Show/hide table
图 2 | g01154310 |
- 断开电缆组件 (4) 和 (5) 。
Show/hide table
图 3 | g01154311 |
- 断开管子组件 (6) 。
Show/hide table
图 4 | g01154312 |
- 拆卸螺栓 (7) 和 (8) 。
Show/hide table
图 5 | g01154314 |
- 拆下夹子 (10) 。
Show/hide table
图 6 | g01154315 |
- 松开螺栓 (9) ,并将电动起动马达 (11) 滑向后方。
- 将适当的起吊设备连接到电动起动马达 (11) 上。 电动起动马达 (11) 的重量约为 27 kg (60 lb)。
- 拆下螺栓 (9) 。
- 使用适当的起吊设备拆下电动起动马达 (11) 。 电动起动马达 (11) 的重量约为 27 kg (60 lb)。
Caterpillar Information System:
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Disassemble
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Install
966H and 972H Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Remove
525C, 535C and 545C Wheel Skidders Grapple Pressure Sensor (Grapple Oil)
C27 and C32 Tier 4 Engines Flywheel
C7 Engines for Caterpillar Built Machines Crankshaft - Install
C7 Engines for Caterpillar Built Machines Crankshaft - Remove
525C, 535C and 545C Wheel Skidders Grapple Check Valve (Pilot)
966H and 972H Wheel Loaders Engine Supplement Engine Compartment Shield - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove
966H and 972H Wheel Loaders Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Install
966H and 972H Wheel Loaders Engine Supplement Aftercooler Core - Remove and Install
966H and 972H Wheel Loaders Engine Supplement Electric Starting Motor - Install
966H and 972H Wheel Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060} Installation of the Variable Pitch, Angle, and Tilt Blade (S/N: R1W; R2W; R3W) on D6R XL, D6R XW, and D6R LGP Machines{6060}
3500B Series II Marine Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
994F Wheel Loader Machine Systems Diverter Valve (Secondary Steering) - Assemble
2005/03/21 Correction to Testing and Adjusting , "Torque Converter Stall and Implement Pump Double Stall - Test" {3101, 5055, 5084}
3516B Off-Highway Trucks Factory Passwords Worksheet
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Remove
966H and 972H Wheel Loaders Machine Systems Piston Pump (Brake, Hydraulic Fan) - Install
525C, 535C and 545C Wheel Skidders Grapple Grapple Frame
621G, 623G and 627G Wheel Tractor-Scrapers Engine Supplement Radiator Module - Install
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Braking System Hydraulic Tank