Front Drive Housing - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7574 | 连杆支架 | 2 |
开始:
- 拆卸发动机机油滤清器壳体。 参考拆解和组装, "发动机机油滤清器壳体 - 拆卸"。
- 卸下惰轮。 请参阅拆解和组装, "惰轮(前部)- 拆卸和安装"。
- 拆下曲轴前油封。 请参阅拆解和组装, "曲轴前油封 - 拆卸"。
- 断开管 (1) 和 (2)。 拆下盖 (3)。 断开支架 (4)。
Show/hide table
图 2 g01219683 - 断开管 (5)。
Show/hide table
图 3 g01219686 - 拆下螺栓 (6)。 将工具 (A) 和适当的起吊设备连接到前驱动壳体 (7) 上。 前驱动壳体 (7) 的重量约为
363 kg (800 lb) 。 拆下螺栓 (8)。 拆卸前驱动壳体 (7)。Show/hide table图 4 g01267741 - 拆下 O 形密封圈 (9) 和 (10)。
Show/hide table
图 1 | g01219679 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7574 | 连杆支架 | 2 |
B | 1U-8846 | 密封垫密封胶 | 1 |
- 将工具 (B) 涂敷到前驱动壳体的配合面上。 安装 O 形密封圈 (9) 和 (10)。
Show/hide table
图 6 g01219686 - 将工具 (A) 和适当的起吊设备连接到前驱动壳体 (7) 上。 前驱动壳体 (7) 的重量约为
363 kg (800 lb) 。 安装前驱动壳体 (7)。 安装螺栓 (8)。 安装螺栓 (6)。Show/hide table图 7 g01219683 - 连接管 (5)。
Show/hide table
图 8 g01219679 - 连接支架 (4)。 安装盖 (3)。 连接管 (1) 和 (2)。
Show/hide table
图 5 | g01267741 |
注: 检查 O 形密封圈有无磨损或损坏。 如有必要,更换 O 形密封圈。
结束:
- 安装曲轴前油封。 请参阅拆解和组装, "曲轴前油封 - 安装"。
- 安装惰轮。 请参阅拆解和组装, "惰轮(前部)- 拆卸和安装"。
- 安装发动机机油滤清器壳体。 参考拆解和组装, "发动机机油滤清器壳体 - 安装"。
Caterpillar Information System:
3612 and 3616 Engines Fuel Pressure Control Valve - Remove
C32 Petroleum Engines Alternator - Remove and Install
C6.6 Engines for Caterpillar Built Machines Alternator - Test
C6.6 Engines for Caterpillar Built Machines Charging System - Test
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
3500 Engines Fuel Transfer Pump
C32 Petroleum Engines Camshaft - Install
C32 Petroleum Engines Camshaft Bearings - Install
C32 Petroleum Engines Camshaft Bearings - Remove
C175 Generator Set Engines Crankshaft Front Seal - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Seat Support - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Seat Suspension - Remove and Install
C15 On-Highway Engine Fuel Transfer Pump
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Counterweight - Remove and Install
3612 and 3616 Engines Fuel Pressure Control Valve - Install
C32 Petroleum Engines Exhaust Elbow - Remove and Install
C27 and C32 Generator Set Engines Start Relay Circuit - Test
3500 Engines Replacing the ECM
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Final Drive - Assemble
C27 and C32 Engines for Caterpillar Built Machines CID 0001 FMI 06 Cylinder #1 Injector short
C27 and C32 Engines for Caterpillar Built Machines CID 0001 FMI 05 Cylinder #1 Injector open circuit
C27 and C32 Engines for Caterpillar Built Machines CID 0002 FMI 05 Cylinder #2 Injector open circuit
C27 and C32 Engines for Caterpillar Built Machines CID 0002 FMI 06 Cylinder #2 Injector short
C27 and C32 Engines for Caterpillar Built Machines CID 0003 FMI 06 Cylinder #3 Injector short