Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
B | 9U-7222 | Camshaft Bearing Pilot | 1 |
8M-8778 | Taperlock Stud 1/2 - 13 by 1 9/16 inch |
1 | |
C | 9U-7210 | Puller Plate | 1 |
D | 9U-7223 | Alignment Bushing | 1 |
E | 9U-7213 | Backup Plate | 1 |
0S-1621 | Bolt 1/2 - 13 by 1 inch | 1 | |
F | 9U-7214 | Spacer Plate | 1 |
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the No. 7 camshaft bearing (rear), as follows:
- Insert the large end of Tooling (B) into the No. 7 camshaft bore.
- Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B).
- Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B).
Note: Refer to Specifications, "Cylinder Head" for appropriate information for the orientation of the camshaft bearings in the cylinder head.
- Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore.
Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Show/hide tableIllustration 2 g01159756 - Install the No. 6 through No. 2 camshaft bearings, as follows:
- Insert the large end of Tooling (B) into the camshaft bore.
Note: Use Tooling (D) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (D) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B).
- Install Tooling (A) on Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B).
Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.
- Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore.
Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Show/hide tableIllustration 3 g01159758 - Insert the large end of Tooling (B) into the camshaft bore.
- Install the No. 1 camshaft bearing (front), as follows:
- Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (D) on Tooling (B).
- Position camshaft bearing (1) on Tooling (B). Install Tooling (E) and Tooling (F) on Tooling (B).
Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.
Note: Tooling (F) is used to seat the No. 1 camshaft bearing to the correct depth in the camshaft bore.
- Use Tooling (A) in order to pull the No. 1 camshaft bearing into the No. 1 camshaft bore. When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Illustration 1 | g01159754 |
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".