Equalizer Bar - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7519 | Electric Hydraulic Pump Gp | 1 |
| 8S-7611 | Tube | 1 | |
| 8S-7650 | Cylinder As | 1 | |
| 8S-7615 | Pin | 1 | |
| C | 138-7574 | Link Bracket | 2 |
| 140-7742 | Sleeve | 2 | |
| 1U-9200 | Lever Puller Hoist | 1 | |
| F | 5P-4758 | Retaining Ring Pliers As | 1 |
| H | 140-7742 | Sleeve | 2 |
| J | FT-2802 | Puller Plate | 1 |
| 162-4197 | Stud | 1 | |
| 9U-5345 | Nut | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 6V-8237 | Washer | 1 | |
| 5P-8713 | Plate | 1 | |
| K | 1P-0510 | Driver Gp | 1 |
| L | 3S-6224 | Electric Hydraulic Pump Gp | 1 |
| 6V-3170 | Double Acting Cylinder | 1 | |
| 1P-1835 | Bearing Puller Adapter | 1 | |
| 5P-4184 | Tool Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 7X-0533 | Hard Washer | 1 | |
- Use Tooling (J) in order to install bearings (13).
- Use Tooling (F) in order to install four retaining rings (12).
Show/hide table
Illustration 2 g00989070 - Use Tooling (K) in order to install four seals (11).
Show/hide table
Illustration 3 g01228141 - Use Tooling (L) in order to install bearing (10) (not shown).
Show/hide table
Illustration 4 g00989068 - Use Tooling (K) in order to install seal (9) and spacer (8). Repeat for the opposite side.
Show/hide table
Illustration 5 g01228151 Show/hide table
Illustration 6 g01228109 - Attach a suitable lifting device and Tooling (H) to equalizer bar (4) and position equalizer bar (4). The weight of equalizer bar (4) is approximately
227 kg (500 lb) . - Use Tooling (C), Tooling (H), and a suitable lifting device in order to support equalizer bar (4).
Show/hide table
Illustration 7 g01228179 - Reposition the suitable lifting device and reposition equalizer bar (4).
Show/hide table
Illustration 8 g00989382 - Install pin assembly (7).
- Install bolt (6).
- Remove Tooling (C) and the suitable lifting device.
Show/hide table
Illustration 9 g00989384 - Install pin (5).
Show/hide table
Illustration 10 g00989408 - Use Tooling (A) in order to lower the front corner of the machine that is opposite of the side that is being worked on.
Show/hide table
Illustration 11 g00989059 - Install cover (3).
- Connect tube assembly (1) and grease hose assembly (2).
Show/hide table
| |
| Illustration 1 | g00989071 |
End By:
- Install the track roller frame. Refer to Disassembly and Assembly, "Track Roller Frame -Install".
- Install the bottom guard. Refer to Disassembly and Assembly, "Bottom Guard - Install".
Caterpillar Information System:
C15 Petroleum Generator Set Engines Gear Group (Front)
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
3046 Engine for Caterpillar Built Machines Flywheel Housing - Inspect
C15 Petroleum Generator Set Engines Electronic Unit Injector Rocker Arm
C4.4 (Mech) Industrial Engine Battery - Test
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540} Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540}
980G Series II Wheel Loader Electrohydraulic System Hydraulic Fan Speed - Test and Adjust
C7 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Roller Frame - Install
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
963C Track-Type Loader Hydraulic System Lift Cylinder
963C Track-Type Loader Hydraulic System Tilt Cylinder
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove