Pistons and Connecting Rods - Remove
拆卸步骤
开始:
- 拆下缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
- 卸下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动曲轴,直到连杆盖位于下止点。
Show/hide table
图 1 | g01126088 |
- 在所有连杆和连杆盖 (2) 上作识别标记。 该编号必须与气缸号一致。
- 拆下螺栓 (1) 和连杆盖 (2) 。
- 从连杆盖 (2) 上拆下连杆轴承 (4) 的下半部分。
Show/hide table
图 2 | g01126089 |
- 推动活塞和连杆远离曲轴。 从连杆 (3) 上拆下连杆轴承 (4) 的上半部分。
- 从缸体上拆下活塞和连杆 (3) 。
Caterpillar Information System:
963C Track-Type Loader Hydraulic System Tilt Cylinder
963C Track-Type Loader Hydraulic System Lift Cylinder
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
D6N Track-Type Tractor Power Train Track Roller Frame - Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Disassemble" {3030, 3160}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Transmission Control (Shift Lever)
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Assemble" {3030, 3160}
963C Track-Type Loader Capacities (Refill)
Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073} Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073}
2003/06/09 New Tilt Cylinder and Lines Are Now Used {5057, 5104}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Metering Pump (HMU) - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Control Valve (Service) - Remove and Install
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install