Front Track Roller Frame - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
B | 154-6182 | Forcing Bolt | 2 |
C | 1U-9202 | Lever Puller Hoist | 2 |
- Release the track tension. Refer to Operation and Maintenance, "Track - Check/Adjust".
Show/hide table
Illustration 1 g00987970 - Position master link (1) and the block, as shown.
Show/hide table
Illustration 2 g00987971 - Attach a suitable lifting device to the track, as shown.
Show/hide table
Illustration 3 g00987973 - Position suitable cribbing, as shown.
- Remove bolts (2).
- Remove track (3).
- Position the track out of the way.
Show/hide table
Illustration 4 g00987975 - Attach a suitable lifting device to master link (1). Apply tension to the master link. Remove the cribbing.
Show/hide table
Illustration 5 g00987976 - Remove bolts (4).
Show/hide table
Illustration 6 g00987978 - Attach Tooling (A) and a suitable lifting device to front track roller (5). Apply lifting tension to the front track roller frame.
Show/hide table
Illustration 7 g00987979 - Remove bolts (6) from cover (7).
- Repeat Step 11 for the opposite side.
Show/hide table
Illustration 8 g00987980 - Install Tooling (B) in order to remove cover (7).
Note: Drain the oil into a suitable container.
- Repeat Step 13 for the opposite side.
- Use a pry bar in order to remove the front track roller.
Show/hide table
Illustration 9 g00988287 - Partially remove front track roller (5) and install Tooling (C). Attach a suitable lifting device to front track roller (5).
- Remove front track roller (5). The weight of front track roller (5) is approximately
385 kg (850 lb) .Note: Drain the oil into a suitable container.
Show/hide tableIllustration 10 g00988288 - Remove seal (8) and bearing (10) from front track roller frame (9), if necessary.
Caterpillar Information System:
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Install
C15 Petroleum Generator Set Engines Gear Group (Front)
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
3046 Engine for Caterpillar Built Machines Flywheel Housing - Inspect
C15 Petroleum Generator Set Engines Electronic Unit Injector Rocker Arm
C4.4 (Mech) Industrial Engine Battery - Test
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540} Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540}
D6N Track-Type Tractor Power Train Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Roller Frame - Install
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
963C Track-Type Loader Hydraulic System Lift Cylinder
963C Track-Type Loader Hydraulic System Tilt Cylinder
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Disassemble" {3030, 3160}