Track Roller Frame - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7519 | Electric Hydraulic Pump Gp | 1 |
| 8S-7611 | Tube | 1 | |
| 8S-7650 | Cylinder As | 1 | |
| 8S-7615 | Pin | 1 | |
| C | 8M-4858 | Adapter | 1 |
| 9U-5339 | Adapter | 1 | |
| 4C-9634 | Puller Stud | 1 | |
| 3S-6224 | Electric Hydraulic Pump Gp | 1 | |
| 9U-6832 | Nut | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| D | 8M-4858 | Adapter | 1 |
| 1P-1839 | Bearing Puller Adapter | 1 | |
| 4C-9634 | Puller Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 3S-6224 | Electric Hydraulic Pump Gp | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| E | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
 |
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
 |
- Use Tooling (C) in order to install bearing (8) . Bearing Surface (X) must be installed even with the Housing Surface (W) .
Note: The grooves in bearing (8) must be installed horizontally.
Show/hide table
 | |
| Illustration 1 | g00988916 |
Show/hide table
 | |
| Illustration 2 | g01926058 |
- Use Tooling (D) in order to install bearing (9) . Bearing Surface (Z) must be installed even with the Housing Surface (Y) .
Note: The grooves in bearing (9) must be installed horizontally.
Show/hide table
 | |
| Illustration 3 | g00988917 |
Show/hide table
 | |
| Illustration 4 | g01926060 |
- Attach a suitable lifting device to track roller frame (5) at the rear lifting point and the front lifting point.
Show/hide table
 | |
| Illustration 5 | g00988758 |
- Position track roller frame (5) . The weight of track roller frame (5) is approximately 1588 kg (3500 lb).
- Install pin assembly (7) and bolt (6) .
Show/hide table
 | |
| Illustration 6 | g00988755 |
- Install O-ring seal (10) onto cover (2) .
Show/hide table
 | |
| Illustration 7 | g00988762 |
- Apply Tooling (E) to bolts (3) . Position plate (4) and install bolts (3) . Tighten bolts (3) to a torque of 570 ± 80 N·m (420 ± 59 lb ft).
Show/hide table
 | |
| Illustration 8 | g00988751 |
Note: Never reuse bolts (3) . Replace bolts (3) with new bolts.
- Position cover (2) and install bolts (1) . Tighten bolts (1) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
Show/hide table
 | |
| Illustration 9 | g00988742 |
- Use Tooling (A) in order to lower the front of the machine.
Show/hide table
 | |
| Illustration 10 | g00988556 |
- Use Tooling (A) in order to lower the rear of the machine.
Show/hide table
 | |
| Illustration 11 | g00988555 |
- Fill the oil reservoir for the pivot shaft. Refer to Operation and Maintenance, "Pivot Shaft Oil Level - Check".
End By: Connect the track. Refer to Disassembly and Assembly, "Track - Separate".
Caterpillar Information System:
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Install
C15 Petroleum Generator Set Engines Gear Group (Front)
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
963C Track-Type Loader Hydraulic System Lift Cylinder
963C Track-Type Loader Hydraulic System Tilt Cylinder
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Disassemble" {3030, 3160}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Transmission Control (Shift Lever)
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Assemble" {3030, 3160}
963C Track-Type Loader Capacities (Refill)