Crankshaft Main Bearings - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 2P-5518     | 主轴承工具     | 1     |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下固定曲轴主轴承盖 (2) 的螺栓 (1) 。 拆卸曲轴主轴承盖 (2) 。
Show/hide table
图 1 | g00988316 |
- 从曲轴主轴承盖 (2) 上拆下曲轴主轴承的下半部分。
- 利用下述步骤拆下曲轴主轴承的上半部分:
- 转动曲轴,使工具 (A) 能够安装在曲轴轴颈中。 安装工具 (A) 。
- 转动曲轴,以便拆下曲轴主轴承的上半部分。 工具 (A) 必须首先接触与曲轴主轴承凸舌端相对的曲轴主轴承。 为了先将凸舌取出,曲轴必须按正确的方向旋转。
- 检查曲轴主轴承的状况。 请参阅可复用零件操作指南, SEBF8009, "主轴承和连杆轴承"或参阅可复用零件操作指南, SEBV0544, "发动机轴承和曲轴"。
Show/hide table
图 2 | g00988318 |
Show/hide table
注意 |
---|
如果曲轴按错误的方向旋转,曲轴主轴承的锁键会在曲轴和缸体之间移动,这可能导致曲轴和缸体同时或其中之一损坏。 |
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Transmission Control (Shift Lever)
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Disassemble" {3030, 3160}
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
963C Track-Type Loader Hydraulic System Tilt Cylinder
963C Track-Type Loader Hydraulic System Lift Cylinder
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
D6N Track-Type Tractor Power Train Track Roller Frame - Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Assemble" {3030, 3160}
963C Track-Type Loader Capacities (Refill)
Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073} Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073}
2003/06/09 New Tilt Cylinder and Lines Are Now Used {5057, 5104}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Metering Pump (HMU) - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Control Valve (Service) - Remove and Install
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Assemble
613C Series II Wheel Tractor-Scraper Hydraulic System Vane Motor (Elevator)