Gear Group (Front)
Show/hide table
图 1 | g02574476 |
(1) 水泵主动齿轮 (5) 齿轮组件 (6) 空气压缩机主动齿轮(如有配备) (7) 齿轮组件 (8) 输油泵齿轮 (10) 曲轴齿轮 (11) 机油泵主动齿轮 |
注: 当松开任何螺栓或螺母以进行维修时,参考以下步骤:
1. 拆下螺栓或螺母。
2. 用钢丝刷清洁螺栓、螺母和/或螺柱。
3. 在装配前,向螺栓、螺母和/或螺柱的螺纹上涂覆蓝色 Loctite 242。
4. 允许使用预先涂覆了螺纹锁固胶的新螺栓。
5. 将螺栓、螺母和/或螺柱拧紧至标准扭矩。
注: 参考测试和调整, "齿轮总成(前)- 正时",以了解齿隙调整步骤。
Show/hide table
208-9490 前齿轮总成 、 207-0449 前齿轮总成 和 248-6767 前齿轮总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
A     | -     | -     | 拧紧枢轴螺栓前,用仪表对凸轮轴齿轮 (3) 和齿轮组件 (5) 的中心之间的距离 (A) 进行设置,以便获得 0.3556 ± 0.254 mm (0.0140 ± 0.010 in) 的齿轮齿隙。     |
Show/hide table
图 2 | g02574477 |
齿轮组枢轴的拧紧顺序 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
2     | 1     | 197-4971 枢轴     | 按照以下顺序将齿轮组组件上枢轴的五个螺栓拧紧至标准扭矩。 请参考图 2 - 1、3、4、5、2、1、2、3、4、5、1     |
Show/hide table
图 3 | g02574478 |
Show/hide table
图 4 | g02574479 |
凸轮轴齿轮的拧紧顺序 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     |
4     |     | -     | 当 1 号活塞处于上死点时,将凸轮轴齿轮上的正时标记与前壳体上的正时标记对准。     |
9     |     | -     | 将曲轴齿轮上的正时标记与齿轮组组件上的正时标记对准。     |
13     | 1     | 031-3185 螺栓     | 使用以 50/50 比例混合的 8T-2998 润滑剂 与清洁的发动机机油润滑 O 形密封圈 (12) 。 螺栓 (13) 的拧紧顺序 1、4、2、5、3、6、1、4 将螺栓 (13) 拧紧至扭矩为 240 ± 40 N·m (177 ± 30 lb ft)     |
14     | -     | -     | 将止推片的油槽朝向齿轮组件 (7) 的端面安装。     |
15     | -     | -     | 将止推片的油槽朝向齿轮组件 (5) 的端面安装。     |
16     | -     | -     | 将止推片的油槽朝向齿轮组组件 (2) 的端面安装。     |
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
3046 Engine for Caterpillar Built Machines Flywheel Housing - Inspect
C15 Petroleum Generator Set Engines Electronic Unit Injector Rocker Arm
C4.4 (Mech) Industrial Engine Battery - Test
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540} Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540}
980G Series II Wheel Loader Electrohydraulic System Hydraulic Fan Speed - Test and Adjust
C7 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
2003/10/27 Special Instruction, REHS1522 , "Instruction Book for the Lincoln Quicklub® Automatic Lubrication System for the 988G Model Wheel Loaders" is Available {7540}
D6N Track-Type Tractor Power Train Equalizer Bar - Install
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Front Track Roller Frame - Install
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Roller Frame - Install
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
963C Track-Type Loader Hydraulic System Lift Cylinder
963C Track-Type Loader Hydraulic System Tilt Cylinder