Front Track Roller Frame - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Bracket | 2 |
C | 1U-9202 | Lever Puller Hoist | 2 |
D | 4C-4032 | Bearing Mount Compound | 1 |
E | 4C-5592 | Anti-Seize Compound | 1 |
- Install bearing (10) and seal (8) into front track roller frame (9), if necessary.
Show/hide table
Illustration 2 g00988364 - Attach Tooling (A) and Tooling (C) to front track roller frame (9).
- Position front track roller frame (9). The weight of front track roller frame (9) is approximately
385 kg (850 lb) . - Use Tooling (C) in order to pull front track roller frame (9) into the original position.
Show/hide table
Illustration 3 g00987979 - Apply Tooling (D) to cover (7).
- Position cover (7).
- Install bolts (6). Tighten bolts (6) to a torque of
105 ± 20 N·m (77 ± 15 lb ft) . - Repeat Steps 5 through 7 for opposite side.
Show/hide table
Illustration 4 g00987978 - Remove Tooling (A).
Show/hide table
Illustration 5 g00987976 - Install bolts (4).
Show/hide table
Illustration 6 g00987975 - Attach a suitable lifting device to master link (1). Install the cribbing.
Show/hide table
Illustration 7 g00987971 Show/hide tableIllustration 8 g00987973 - Attach a suitable lifting device to the track, as shown.
- Position the track.
- Position track (3).
- Apply Tooling (E) to bolts (2).
- Install bolts (2). Tighten bolts (2) to a torque of
400 ± 70 N·m (295 ± 52 lb ft) . - Remove the cribbing.
- Adjust the track tension. Refer to Operation and Maintenance Manual, "Track - Check/Adjust".
Show/hide table
Illustration 1 | g00988288 |
Caterpillar Information System:
D6N Track-Type Tractor Power Train Front Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Remove
D6N Track-Type Tractor Power Train Equalizer Bar - Install
C15 Petroleum Generator Set Engines Gear Group (Front)
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
3046 Engine for Caterpillar Built Machines Flywheel Housing - Inspect
C15 Petroleum Generator Set Engines Electronic Unit Injector Rocker Arm
C4.4 (Mech) Industrial Engine Battery - Test
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
D6N Track-Type Tractor Power Train Pivot Bar-Remove and Install
D6N Track-Type Tractor Power Train Track Adjuster - Remove and Install
D6N Track-Type Tractor Power Train Track Roller Frame - Remove
D6N Track-Type Tractor Power Train Track Roller Frame - Install
Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000}
3044C Industrial Engine and Engines for Caterpillar Built Machines Glow Plugs
963C Track-Type Loader Hydraulic System Lift Cylinder
963C Track-Type Loader Hydraulic System Tilt Cylinder
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Disassemble" {3030, 3160}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Transmission Control (Shift Lever)