Camshaft Gear - Remove and Install
拆卸步骤
开始:
- 拆下凸轮轴。 请参考拆解和组装, "凸轮轴 - 拆卸"。
- 用保护罩包裹凸轮轴来防止损坏凸轮轴。
- 将凸轮轴组件放置在适当的压具中。 将凸轮轴 (2) 从凸轮轴齿轮 (1) 压出。
Show/hide table
图 1 | g00987675 |
Show/hide table
注意 |
---|
从驱动齿轮挤压时不要使凸轮轴落到地上。 同时确认凸轮轴上的凸轮与压力板不匹配。 |
- 如有必要,从凸轮轴拆卸键 (3) 。
安装步骤
- 加热凸轮轴齿轮。
注: 不要使用喷枪加热凸轮轴齿轮。
- 对正凸轮轴中的键 (3) 与凸轮轴齿轮中的槽(键槽)。
Show/hide table
图 2 | g00987675 |
- 将凸轮轴齿轮 (1) 安装到凸轮轴 (2) 的端部。
End By: 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
2003/10/27 Special Instruction, REHS1522 , "Instruction Book for the Lincoln Quicklub® Automatic Lubrication System for the 988G Model Wheel Loaders" is Available {7540}
615C Series II Wheel Tractor-Scraper Air System and Brakes Pressure Protection Valve (Brake Air System)
615C Series II Wheel Tractor-Scraper Air System and Brakes Differential Lock Control
611 and 615C Series II Wheel Tractor-Scrapers Steering System Steering System Troubleshooting
611 and 615C Series II Wheel Tractor-Scrapers Steering System Piston Pump (Secondary Steering)
611 and 615C Series II Wheel Tractor-Scrapers Steering System General Information
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Disassemble
651E and 657E Wheel Tractor-Scrapers Hydraulic System Relief Valve (Push-Pull) - Test and Adjust
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Bucket Wear Plates - Inspect/Replace
C7 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C7 Engines for Caterpillar Built Machines Rocker Shaft - Assemble
980G Series II Wheel Loader Electrohydraulic System Hydraulic Fan Speed - Test and Adjust
Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540} Support literature for the Lincoln Industrial Quicklub System for the 988G Wheel Loader{7540}
2003/03/24 New Flash Software Allows Calibrations of the Power Train to be Performed by Using the Caterpillar Electronic Technician {0783, 0785, 7620}
C4.4 (Mech) Industrial Engine Battery - Test
C15 Petroleum Generator Set Engines Electronic Unit Injector Rocker Arm
3046 Engine for Caterpillar Built Machines Flywheel Housing - Inspect
2003/06/23 Correction to Testing And Adjusting , "Transmission Testing and Location of The Pressure Taps" {3030, 3073}
2003/04/21 Correction to Testing and Adjusting , "Pressure Tap Locations" {3030}
C7 Engines for Caterpillar Built Machines Unit Injector - Remove
C7 Engines for Caterpillar Built Machines Unit Injector - Install
C15 Petroleum Generator Set Engines Gear Group (Front)
D6N Track-Type Tractor Power Train Equalizer Bar - Install