Assembly Procedure
Show/hide table
Table 1
| Required Tools |
| Tool |
Part Number |
Part Description |
Qty |
| A |
4C-4030 |
Thread Lock Compound |
1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Show/hide table
|
 |
|
| Illustration 1 | g00987601 |
Show/hide table
|
 |
|
| Illustration 2 | g00987603 |
- Use a suitable allen wrench and the flats of spool (48) in order to install orifice (57) . Tighten orifice (57) to a torque of 2.5 ± 0.5 N·m (22.13 ± 4.43 lb in).
- Repeat this procedure for the remaining cartridge assemblies.
Show/hide table
|
 |
|
| Illustration 3 | g00987596 |
- Install spool (48) .
- Install O-ring seals (56) .
Show/hide table
|
 |
|
| Illustration 4 | g00987594 |
Show/hide table
 |
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
 |
Note: Use the flats of cage (41) to install stop (55) .
- Install O-ring seal (54) .
- Install spring (53) and stop (55) . Tighten stop (55) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
Show/hide table
|
 |
|
| Illustration 5 | g00987590 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
Show/hide table
|
 |
|
| Illustration 6 | g00987592 |
- Install spring (50) on spool (48) . Compress spring (50) and install ball (52) and retainers (49) .
Show/hide table
|
 |
|
| Illustration 7 | g00987587 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
Show/hide table
|
 |
|
| Illustration 8 | g00987589 |
- Install O-ring seals (46) and (47) .
- Install spring (45) and plunger (43) on adapter (40) .
- Install retainer (44) and snap ring (42) .
Show/hide table
|
 |
|
| Illustration 9 | g00987586 |
- Connect adapter (40) to cage (41) . Tighten adapter (40) to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Show/hide table
|
 |
|
| Illustration 10 | g00987584 |
- Install screen assembly (39) . Install O-ring seal (38) on seal connector (36) .
Show/hide table
|
 |
|
| Illustration 11 | g00987582 |
- Install O-ring seal (37) on plug (35) . Repeat for the remaining 44 plugs.
Show/hide table
|
 |
|
| Illustration 12 | g00987580 |
- Install seal connector (36) and the cap assembly. Tighten seal connector (36) to a torque of 28 ± 4 N·m (21 ± 3 lb ft).
- Install plugs (35) . Tighten plugs (35) to a torque of 12 ± 3 N·m (105 ± 27 lb in). Repeat for the remaining 44 plugs.
Note: There are 45 O-ring seals on plugs (35) in the three valve bodies.
- Install cartridge assembly (34) .
Show/hide table
|
 |
|
| Illustration 13 | g00987579 |
- Install adapters (33) and the O-ring seals.
Show/hide table
|
 |
|
| Illustration 14 | g00987576 |
- Connect the valve bodies. Install hex bolts (32) and the nuts. Tighten hex bolts (32) to a torque of 12 ± 3 N·m (105 ± 27 lb in).
Show/hide table
|
 |
|
| Illustration 15 | g00987574 |
- Install O-ring seals (29) on adapters (30) and (31) .
Show/hide table
|
 |
|
| Illustration 16 | g00987572 |
- Install the three valve bodies on plate (27) .
- Install adapter (26) and plates (25) .
Show/hide table
|
 |
|
| Illustration 17 | g00987541 |
- Install cartridge assemblies (24) .
Show/hide table
|
 |
|
| Illustration 18 | g00987534 |
- Install adapters (23) .
Show/hide table
|
 |
|
| Illustration 19 | g00987532 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Install the spring and screen assembly (22) . Install O-ring seal (21) .
Show/hide table
|
 |
|
| Illustration 20 | g00987531 |
- Connect the valve assembly and install bolts (20) .
Show/hide table
|
 |
|
| Illustration 21 | g00987530 |
- Install adapter (19) . Tighten adapters (19) to a torque of 45 ± 4 N·m (33 ± 3 lb ft).
Show/hide table
|
 |
|
| Illustration 22 | g00987527 |
- Install bracket (18) , bolts (16) , and bolts (17) . Tighten bolts (16) to a torque of 12 ± 3 N·m (105 ± 27 lb in). Apply Tooling (A) to the threads of bolt (17) . Tighten bolt (17) to a torque of 28 ± 4 N·m (21 ± 3 lb ft).
Show/hide table
|
 |
|
| Illustration 23 | g00987510 |
Show/hide table
|
 |
|
| Illustration 24 | g00686158 |
Show/hide table
|
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
|
- Install spacer (11) and swivel (15) . Install washer (15) , spring (14) , nut (13) , and pin (12) . Repeat for the opposite side of plate (9) .
- Use Dimension (C) as a reference. Dimension (C) equal 12.15 ± 0.06 mm (0.478 ± 0.002 inch).
- Apply Tooling (A) to all the threads.
- Tighten nut (13) to a torque of 12 ± 3 N·m (105 ± 27 lb in).
- Tighten plate (9) to a torque of 90 ± 10 N·m (66 ± 7 lb ft).
Show/hide table
|
 |
|
| Illustration 25 | g00987508 |
- Install lever assemblies (8) . Install clips (6) and pins (7) .
Show/hide table
|
 |
|
| Illustration 26 | g00987505 |
- Install boots (5) and rod (4) . Tighten nuts (3) .
Show/hide table
|
 |
|
| Illustration 27 | g00987504 |
- Install knob assembly (2) and screw (1) on the rod.
End By:
Install the pilot operated hydraulic control. Refer to Disassembly and Assembly, "Pilot Operated Hydraulic Control - Install" for the machine that is being serviced.
