Draft Frame Bearings - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-1840 | Bearing Puller Adapter | 1 |
6V-4035 | Sleeve | 1 | |
5P-4184 | Stud | 1 | |
6V-3175 | Cylinder Group | 1 | |
350-7768 | Electric Hydraulic Pump Gp (115V) | - | |
350-7769 | Electric Hydraulic Pump Gp (230V) | - | |
3S-1356 | Nut | 1 | |
4K-0684 | Hard Washer | 1 |
Start By:
- Separate the tractor and the scraper. Refer to Disassembly and Assembly, "Tractor and Scraper - Separate". The information is in this manual.
- Remove grease fitting (1) from draft frame (2).
Show/hide table
Illustration 2 g00452279 - Use Tool (A) to remove sleeve bearing (3) from draft frame (2).
- Repeat this procedure for the upper draft frame bearing.
Show/hide table
Illustration 1 | g00452308 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-7693 | Bearing Puller Adapter | 1 |
5F-7693 | Spacer | 1 | |
5P-4184 | Stud | 1 | |
6V-3175 | Cylinder Group | 1 | |
6V-9061 | Hand Pump | 1 | |
7H-7539 | Nut | 1 |
- Use Tool (A) to install sleeve bearing (3) to draft frame (2). Install the sleeve bearing until the sleeve bearing is centered in the draft frame.
Show/hide table
Illustration 4 g00452308 - Install grease fitting (1) to draft frame (2).
- Repeat this procedure for the upper draft frame bearing.
Show/hide table
Illustration 3 | g00452279 |
End By:
- Connect the tractor and the scraper. Refer to Disassembly and Assembly, "Tractor and Scraper - Connect". The information is in this manual.
Caterpillar Information System:
994D Wheel Loader Ether Starting Aid Cylinder - Replace
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Install
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Remove
924Gz Wheel Loader Warranty Information
966G and 972G Wheel Loaders Power Train Differential and Bevel Gear - Install
3116 Engine Supplement for 953C Track-Type Loader Alternator Belt - Remove and Install
994D Wheel Loader Engine Oil and Filter - Change
928G Wheel Loader Tilt Cylinder Bearings and Bucket Linkage Bearings - Lubricate
994D Wheel Loader Engine Oil Level - Check
994D Wheel Loader Engine Mounts - Inspect
994D Wheel Loader Engine Crankcase Breather - Clean
994D Wheel Loader Engine Components - Replace/Install Reman
950G Wheel Loader and 962G Wheel Loader Electrohydraulic System Lift Kickout Positioner - Adjust
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Disassemble
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Assemble
966G and 972G Wheel Loaders Power Train Heat Exchanger (Axle Oil Cooler) - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Governor - Disassemble
994D Wheel Loader Fuel System - Prime
994D Wheel Loader Fuel System Primary Filter - Clean/Inspect/Replace
615C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Disassemble
613C Series II Wheel Tractor-Scraper Machine Systems Ejector - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Ejector - Install
966G and 972G Wheel Loaders Power Train Torque Converter from Transmission, Output Transfer Gears - Separate
3176C and 3196 Engines for Caterpillar Built Machines Rocker Shaft