Ejector - Remove
Removal Procedure
Start By:
- Remove the elevator. Refer to Disassembly and Assembly, "Elevator - Remove". The information is in this manual.
- Move the ejector to the front of the scraper bowl.
- Remove three bolts (1) and plate (2) from ejector (3) .
Show/hide table
Illustration 1 | g00454926 |
- Place suitable cribbing under the ejector cylinder, as shown.
Show/hide table
Illustration 2 | g00442085 |
- Attach a lifting chain and a hoist to the ejector. Use a hammer and a brass rod to remove pin (4) from ejector (3) .
Show/hide table
Illustration 3 | g00454927 |
- Remove bolt (5) from bracket (6) . Remove guide roller (7) and roller shaft (8) from bracket (6) . Repeat the procedure for the other side of the ejector.
Show/hide table
Illustration 4 | g00454928 |
- Remove two bolts (9) and bar (10) from the scraper bowl. Repeat the procedure for the other side of the scraper bowl.
Show/hide table
Illustration 5 | g00455003 |
- Use a hoist to move the ejector forward in order to remove the ejector support roller from the track assembly.
Show/hide table
Illustration 6 | g00445443 |
- Remove the ejector from the scraper bowl. The ejector weighs 508 kg (1120 lb) .
Show/hide table
Illustration 7 | g00455006 |
Caterpillar Information System:
615C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Disassemble
994D Wheel Loader Fuel System Primary Filter - Clean/Inspect/Replace
994D Wheel Loader Fuel System - Prime
3304B and 3306B Engines for Caterpillar Built Machines Governor - Disassemble
966G and 972G Wheel Loaders Power Train Heat Exchanger (Axle Oil Cooler) - Remove and Install
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Assemble
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Disassemble
950G Wheel Loader and 962G Wheel Loader Electrohydraulic System Lift Kickout Positioner - Adjust
615C Series II Wheel Tractor-Scraper Machine Systems Draft Frame Bearings - Remove and Install
994D Wheel Loader Ether Starting Aid Cylinder - Replace
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Install
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Ejector - Install
966G and 972G Wheel Loaders Power Train Torque Converter from Transmission, Output Transfer Gears - Separate
3176C and 3196 Engines for Caterpillar Built Machines Rocker Shaft
Test Sequence For Caterpillar 7000 Series Fuel Nozzles{1254} Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Removal and Installation of 138-0006 Retainer and 138-0007 Retainer Removal and Installation of 138-0006 Retainer and 138-0007 Retainer
3116 Engine Supplement for 953C Track-Type Loader Engine - Remove
994D Wheel Loader Fuel Tank Cap and Strainer - Clean
994D Wheel Loader Power Train Torque Converter Troubleshooting
994D Wheel Loader Fuel Tank Water and Sediment - Drain
615C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Assemble
3116 Engine Supplement for 953C Track-Type Loader Engine - Install
D6G Track-Type Tractor Power Train Bevel Gear and Shaft - Remove