Governor - Disassemble
解体步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 6V-2163     | 弹簧卡箍     | 1     |
C     | 1P-1855     | 挡圈钳     | 1     |
开始:
- 拆卸燃油喷油泵壳体和调速器。 请参考解体与组装, "燃油喷油泵壳体与调速器 - 拆卸"。
注: 要拆下调速器,以便解体燃油喷油泵壳体,进行第 1、2、16、22、24、25、26、27、30、32 和 34。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从调速器 (2) 上拆下燃油比控制阀 (1) 。
Show/hide table
图 1 | g00453006 |
- 拆下六根螺栓 (3) 、两根螺栓 (5) 、壳体 (4) 和密封垫。
Show/hide table
图 2 | g00453007 |
注: 图 2 所示为仍连接的燃油比控制阀。
- 拆下调速器弹簧 (7) 、底座 (6) 和垫圈。
Show/hide table
图 3 | g00453008 |
- 拆下六根螺栓 (8) 、盖 (9) 和密封垫。 使用工具 (A) 拆下密封件 (10) 。
Show/hide table
图 4 | g00453009 |
- 拆卸低怠速调节螺钉 (12) 和弹簧 (11) 。
Show/hide table
图 5 | g00453010 |
- 拆下轴组件 (15) 和杆 (14) 和 (13) 。
Show/hide table
图 6 | g00453011 |
- 从两个销 (17) 上拆下两个卡环 (19) 。 拆下两个销 (17) 。 拆下板 (16) 和止动块 (18) 。
Show/hide table
图 7 | g00453012 |
- 拆下销 (21) 和 (22) ,然后拆下弹簧 (20) 。
Show/hide table
图 8 | g00453014 |
- 拆下两根螺栓 (23) 和垫圈,然后拆下接头 (24) 、联轴节和 O 型密封圈。
Show/hide table
图 9 | g00453015 |
- 通过 O 型密封圈拆下触片 (27) 和主体 (28) 。
- 拆下两根螺栓 (29) 和垫圈,然后拆下盖 (30) 和密封垫。
- 拆下两个螺母和垫圈 (26) ,然后拆下切断电磁阀 (25) 和密封垫。
- 拆下轴 (31) 和垫圈 (32) 。
Show/hide table
图 10 | g00453016 |
- 仅在必须更换时拆下单向阀 (33) 。
Show/hide table
图 11 | g00453017 |
注: 拆卸时单向阀将损坏。 仅在必须更换时拆下单向阀 (33) 。
- 拆下密封件 (34) 和调节螺钉 (35) 。
Show/hide table
图 12 | g00453018 |
- 从燃油喷油泵壳体拆下螺栓 (36) 、壳体 (37) 和密封垫。
Show/hide table
图 13 | g00453019 |
- 拆下螺栓 (38) 然后拆下扭矩控制装置 (39) 。
Show/hide table
图 14 | g00453557 |
典型示例 |
- 解体扭距控制装置 (39) ,并检查隔套、弹簧和隔离体有无损坏或磨损。 用新零件更换所有磨损或损坏的零件。
- 拆下两根螺栓 (40) 和块 (41) 。
Show/hide table
图 15 | g00453558 |
- 拆下将环套 (42) 固定到螺栓 (44) 上的螺栓。 拆下环套 (42) 、弹簧 (43) 和螺栓 (44) 。
Show/hide table
图 16 | g00453559 |
- 如果需要更换环套,从环套 (42) 上拆下止动螺钉。
- 拆下三根螺栓 (46) ,然后拆下调速器伺服器 (45) 。 调速器伺服器 必须旋转,以便从齿条调节器上释放。
Show/hide table
图 17 | g00453560 |
- 拆下锁环 (50) 、支座 (53) 、连杆弹簧 (52) 和衬套 (51) 。 从阀门 (47) 中间的凹槽中拆下其它锁环 (50) 。 拆下阀门 (47) 、衬套 (48) 和活塞 (49) 。 必须向下推活塞,才能将其拆下。 从衬套 (48) 上拆下 O 型密封圈。 拆下销 (55) 和杆 (56) 。
Show/hide table
图 18 | g00453632 |
- 使用工具 (A) 将弹簧 (58) 保持在压缩状态,以便拆下环 (57) 。 弹簧 (58) 用于在燃油喷油泵壳体中的凸轮轴止推轴承上施加一定的预载荷。
Show/hide table
图 19 | g00453633 |
Show/hide table
图 20 | g00453634 |
- 拆下环 (57) 然后慢慢释放工具 (A) 。
- 拆下轴承 (60) 、衬套 (59) 和弹簧 (58) 。
Show/hide table
图 21 | g00453635 |
- 拆下环 (61) 和缓冲器组件 (62) 。
Show/hide table
图 22 | g00453636 |
- 使用工具 (C) 拆下卡环 (68) 。 拆下环 (67) 和轴 (66) 。
Show/hide table
图 23 | g00453637 |
- 从弹簧 (64) 上拆下支座 (65) ,并从支座 (63) 上拆下弹簧 (64) 。
- 拆下举升器 (69) 。
Show/hide table
图 24 | g00453665 |
- 拆下环 (70) 、座圈 (71) 和轴承 (72) 。
Show/hide table
图 25 | g00453667 |
- 拆下四根螺栓 (73) 和支架 (74) 。
Show/hide table
图 26 | g00453668 |
- 拆下定位销 (77) 和飞锤 (76) 。 拆下调速器轴 (75) 和从轴 (75) 上无法看到的定位销。
Show/hide table
图 27 | g00453669 |
- 拆下座圈 (78) 和轴承 (79) 。
Show/hide table
图 28 | g00453670 |
Caterpillar Information System:
966G and 972G Wheel Loaders Power Train Heat Exchanger (Axle Oil Cooler) - Remove and Install
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Assemble
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Valve (Oil Manifold) - Disassemble
950G Wheel Loader and 962G Wheel Loader Electrohydraulic System Lift Kickout Positioner - Adjust
615C Series II Wheel Tractor-Scraper Machine Systems Draft Frame Bearings - Remove and Install
994D Wheel Loader Ether Starting Aid Cylinder - Replace
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Install
615C Series II Wheel Tractor-Scraper Machine Systems Hitch Bearings - Remove
924Gz Wheel Loader Warranty Information
966G and 972G Wheel Loaders Power Train Differential and Bevel Gear - Install
3116 Engine Supplement for 953C Track-Type Loader Alternator Belt - Remove and Install
994D Wheel Loader Engine Oil and Filter - Change
994D Wheel Loader Fuel System - Prime
994D Wheel Loader Fuel System Primary Filter - Clean/Inspect/Replace
615C Series II Wheel Tractor-Scraper Machine Systems Elevator Control Valve - Disassemble
613C Series II Wheel Tractor-Scraper Machine Systems Ejector - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Ejector - Install
966G and 972G Wheel Loaders Power Train Torque Converter from Transmission, Output Transfer Gears - Separate
3176C and 3196 Engines for Caterpillar Built Machines Rocker Shaft
Test Sequence For Caterpillar 7000 Series Fuel Nozzles{1254} Test Sequence For Caterpillar 7000 Series Fuel Nozzles {1254}
Removal and Installation of 138-0006 Retainer and 138-0007 Retainer Removal and Installation of 138-0006 Retainer and 138-0007 Retainer
3116 Engine Supplement for 953C Track-Type Loader Engine - Remove
994D Wheel Loader Fuel Tank Cap and Strainer - Clean
994D Wheel Loader Power Train Torque Converter Troubleshooting