E100 Low Engine Oil Pressure Warning
产生此代码的情况:
电子控制模块(ECM)检测到以下情况时:
- 发动机至少已经运转了30秒钟。 一旦发动机转速与低怠速相差不超过50 rpm,这10秒钟的延迟就开始计时。
- 发动机机油压力低于图1中的"警告(Warning)"线长达2秒钟。
Show/hide table
图 1 | g00784705 |
机油压力图 |
Show/hide table
触发水平     | 设定点(秒)     | 复位水平     | 复位时间     |
更多有关信息,请参看图1。     | 2 秒(sec)     | 70 kPa (10 psi)     |
20 秒(sec)     |
直到发动机转速已经连续30秒钟超过0 rpm 时,ECM才将作出反应动作。
系统响应:
ECM将会记录此警告。
无
- 发动机润滑系统可能有问题。
测试步骤 1. 检查有无诊断编码
- 将卡特彼勒电子维修工具(ET)连接到维修工具接头上。
- 将发动机控制置于通电(ON)模式。 发动机应处于停机状态。
- 检查有无任何活动或记录诊断编码。
预期结果:
应无任何诊断编码出现。
结果:
- 与预期结果一致 - 没有任何诊断编码出现。 进行步骤2。
- 与预期结果不符 - 有诊断编码出现。
修复: 纠正导致诊断编码出现的根源。 请参阅本手册"有故障编码出现时的故障诊断与排除"部分中的适当专题。确保修理后故障被排除。
停止
测试步骤 2. 检查发动机机油油位
- 检查发动机机油油位。
预期结果:
发动机机油油位正常。
结果:
- 与预期结果一致 - 发动机机油油位正常。
修复: 请参阅测试与调整, "发动机机油压力 - 测试"。
停止
- 与预期结果不符 - 发动机机油油位低。
修复: 添加发动机机油至正确油位。
停止
Caterpillar Information System:
C-10, C-12, C-15 and C-16 Industrial Engines E096 High Fuel Pressure
3126B Industrial Engines Event Codes
3126B Industrial Engines Diagnostic Codes
3126B Industrial Engines Throttle Position Sensor - Calibrate
3408E and 3412E Engines for Caterpillar Built Machines Lubrication System
2004/08/01 The Removal of the Fuel Recirculation System is Required on Certain Engines. {1274}
3126B Industrial Engines Injection Actuation Pressure Sensor - Test
3126B Industrial Engines Injection Actuation Pressure Control Valve Circuit - Test
2005/04/25 Lockout Valves Shut Off Air Supply in the Service Shop {0699}
3126B Industrial Engines ECM/Personality Module - Test
2004/06/01 New Tightening Procedure for the Oil Filter Line {1307}
3126B Engine for Caterpillar Built Machines Injector Code - Calibrate
2004/12/27 Test Kit Checks Oil Coolers for Leaks {0768, 0781, 0783, 0784}
G3500 Engines Ignition System Spark Plugs - Inspect/Replace
3126B Petroleum Engine Electronic Service Tools
2004/11/01 A New Abrasion Resistant Fuel Line is Now Used {1274}
C15 On-highway Engines Cylinder Head - Remove
C15 On-highway Engines Cylinder Head - Install
2004/08/01 Corrosion-Resistant Sensor and Elbow Are Now Available {1917}
3412E, C30 and C32 Marine Engines Fuel Priming Pump - Remove and Install
3412E, C30 and C32 Marine Engines Fuel Filter Base - Remove and Install
2004/07/01 Engines Are Now Built with Semi-Crowned Lifter Rollers {1209}
2004/07/05 Improved Analysis of Non-Warrantable Failures for Reman Vane Cartridges {5055}
3412E, C30 and C32 Marine Engines Fuel Transfer Pump - Remove