Instrument Panel
仪表盘开关
Show/hide table
图 1 | g00907147 |
仪表盘开关 (1) 转速电位器(SP) (2) 发动机控制开关(ECS) (3) 调压变阻器(VAR) (4) 紧急停车按钮(ESPB) (5) 选配面板照明灯开关 (PLS) |
发动机控制开关(ECS) (2) 决定控制仪表板的状态。 当 ECS 位于 自动(AUTO)位置并且远程启动触点关闭时,GSC 允许发动机起动。 发动机在初始触点打开后也停机。 可以编程设定发动机停机前有 0 至 30 分钟的冷却时间。 出厂设定的冷却时间为 5 分钟。 只要 ECS 开关保持在手动启动(MANUAL START)位置,发动机就将启动和运转。 当 ECS 位于冷却/停止(COOLDOWN/STOP)位置时并且冷却完成,发动机关闭。 在关闭/复位(OFF/RESET)位置,发动机立刻停机,除了紧急停止指示灯之外的所有故障指示灯复位。
按下紧急停止按钮(ESPB) (4) 时,燃油被切断。 通过顺时针旋转 ESPB (4) 重新起动发动机,直至松开开关。 将 ECS 转到关闭/复位(OFF/RESET)位置。 然后将 ECS 转到手动启动(MANUAL START)位置。
调压变阻器 (VAR) (3) 用于将发电机输出电压调节至理想电压。
转速调节电位计(SP) (1) 控制发动机转速。
选装的面板照明灯开关(PLS) (5) 控制面板灯的开和关。
Caterpillar Information System:
HT400 Pumper Fuel System Primary Filter - Replace
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Water Temperature Regulator - Test
C9 On-highway Engines Safety Messages
EMCPII+ for Gas Engines EMCP Electronic Control (Generator Set)
G3600 Engines Exhaust Bypass Valve
C9 Marine Auxiliary and Generator Set Engines Engine Crankcase Breather - Clean
3126E and 3126B Commercial and Truck Engines Product Lifting
3054E Industrial Engine Piston Cooling Jet
3606, 3608, 3612, 3616 and 3618 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Panel View Monitor Connections
3406E and C15 Marine Engines Closed Crankcase Ventilation (CCV) System
G3520B Engines Compressor Bypass
2002/08/05 Guidelines for Water Pump Visual Inspection {1361}
HT400 Pumper Maintenance Interval Schedule
HT400 Pumper Safety Messages
EMCPII+ for Gas Engines Normal Mode
C-10 and C-12 Truck Engines Wastegate Solenoid
C-10 and C-12 Truck Engines Fuel Lines
G3520B Engines MID 033 - CID 0041 - FMI 03 8 Volt DC Supply short to +batt
G3520B Engines MID 033 - CID 0041 - FMI 04 8 Volt DC Supply short to ground
3056E Industrial Engine Engine Oil Filter Bypass Valve
G3600 Engines Fuel Control
C-10, C-12 and C-15 On-highway Engines 0166-11 Rated Engine Power Derate
3054E Industrial Engine Exhaust Manifold
G3520B Engines MID 036 - CID 1720 - FMI 05 Turbo Compressor Bypass Valve Solenoid open