Swivel - Remove and Install - Quick Coupler Dedicated Wedge Lock
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 3E-3879 | Lifting Eye (M16) | 2 |
B | 417-1324 | Jack Stand | 4 |
Start By:
- Remove the hydraulic rotator.
- Remove the quick coupler lock.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned to prevent dirt from entering the internal mechanism.
- Attach Tooling (A) and a suitable lifting device to quick coupler (1).Place quick coupler (1) in vertical position on a suitable cribbing as shown in illustration 1. Refer to the Table 2 for the weight information of quick coupler (1).
Show/hide table
Table 2 Sales Model Part Number Weight of Quick Coupler TRS10 511-7763 192 kg (423 lb) TRS14
TRS18516–6750 202 kg (445 lb) TRS10 511-7765 205 kg (452 lb) TRS14
TRS18516-6748 248 kg (547 lb) TRS23 567-9028 346 kg (763 lb) TRS23 564-1462 252 kg (556 lb) Show/hide tableIllustration 2 g06370900 - Disconnect harness assembly (2) and led lighting (5). Remove bolt (3), lock washer (4), and led lighting (5).
Show/hide table
Illustration 3 g06125004 Note: Mark position of swivel (9) for installation purposes before removal.
- Attach Tooling (A) and a suitable lifting device to quick coupler (1). Lift quick coupler (1) and position on Tooling (B) as shown in illustration 3.
- Remove two screws (6) affixing electric swivel (5) and remove electric swivel (5).
- Remove six bolts (7) and lock washers (8) from swivel (9).
- Remove swivel (9).
Show/hide table
Illustration 4 g06148050 - Remove 10 O-ring seals (10) and dowel pins (11).
Show/hide table
Illustration 1 | g06151613 |
- Install swivel (9) in the reverse order of the removal procedure.
- Install swivel (9) properly on dowel pins (11) and position swivel (9) regarding to quick coupler (1) as shown in the illustration 5.
- Lubricating 10 O-ring seals (10) with oil.
- Tighten six bolts (7) to a torque of
60 N·m (44 lb ft) .
Show/hide tableIllustration 5 g06148050
Caterpillar Information System:
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Cylinder - Remove and Install - Quick Coupler (Dedicated Wedge Lock) Cylinder
Installation of the 520-6470 Blank Hook As. on Certain Wheel Loaders {6102} Installation of the 520-6470 Blank Hook As. on Certain Wheel Loaders {6102}
Incorrect Substitution of the 12 Point Cylinder Head Bolt on all G3500 and 3500 Engines {1100} Incorrect Substitution of the 12 Point Cylinder Head Bolt on all G3500 and 3500 Engines {1100}
H80 S Hydraulic Hammers Tool Retaining Pins - Inspect/Replace
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Cylinder - Remove and Install - Tilt Cylinder
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Steering Control Support
PM820, PM822, and PM825 Cold Planer Track Pad Bolts - Tighten
C9.3B Aftertreatment Systems SCR Catalyst Inlet Temperature Sensor - Test
C9.3B Aftertreatment Systems DEF Pump Motor - Test
C9.3B Aftertreatment Systems ARD Nozzle Heater - Test
C9.3B Aftertreatment Systems ARD Ignition - Test
C7.1 Engines and Generator Sets ARD Failed to Ignite
730C2 and 725C2 Articulated Truck Power Train Differential Pinion - Remove and Install - Front and Rear
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Remove and Install - Quick Coupler S-Type
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Disassemble
C7.1 Engines and Generator Sets ARD Fuel Pressure Is High
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Assemble
<B>Wiper Motor Shaft Breakage on Certain K, L, and M Series Medium Wheel Loaders</B> {7305} <B>Wiper Motor Shaft Breakage on Certain K, L, and M Series Medium Wheel Loaders</B> {7305}
730C2 and 725C2 Articulated Truck Power Train Transfer Case - Remove and Install - Center Axle
730C2 and 725C2 Articulated Truck Power Train Transfer Case - Disassemble - Center Axle
349F and 352F Excavator Machine System Service Tools
349F and 352F Excavator Machine System Diagnostic Capabilities
PM820, PM822, and PM825 Cold Planer Machine Systems Gear Motor - Remove and Install - Ventilation
G3500H Generator Set Engine Coolant Pressure Is High