Swivel - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Rubber Hammer | 1 |
Start By:
- Remove the swivel.
- Remove retaining ring (1) and bearing (2) from swivel crown (3).
Show/hide table
Illustration 2 g06123142 - Remove O-ring seal (4) from bearing (2).
Show/hide table
Illustration 3 g06127290 - Use Tooling (A) to remove swivel crown (3). Remove swivel crown (3).
Show/hide table
Illustration 4 g06123149 - Remove bearing (5) and O-ring seal (6).
Show/hide table
Illustration 5 g06123150 - Remove seals (7).
Show/hide table
Illustration 6 g06123152 - Remove flat face plugs (8), plug assemblies (9), and plug (10) from swivel crown (3).
Show/hide table
Illustration 7 g06127300 - Remove seals (11) from plug assemblies (9) and flat face plugs (8).
Show/hide table
Illustration 8 g06142775 - Remove dowel pins (12).
Show/hide table
Illustration 1 | g06127289 |
Caterpillar Information System:
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Remove and Install - Quick Coupler S-Type
730C2 and 725C2 Articulated Truck Power Train Differential Pinion - Remove and Install - Front and Rear
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Remove and Install - Quick Coupler Dedicated Wedge Lock
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Cylinder - Remove and Install - Quick Coupler (Dedicated Wedge Lock) Cylinder
Installation of the 520-6470 Blank Hook As. on Certain Wheel Loaders {6102} Installation of the 520-6470 Blank Hook As. on Certain Wheel Loaders {6102}
Incorrect Substitution of the 12 Point Cylinder Head Bolt on all G3500 and 3500 Engines {1100} Incorrect Substitution of the 12 Point Cylinder Head Bolt on all G3500 and 3500 Engines {1100}
H80 S Hydraulic Hammers Tool Retaining Pins - Inspect/Replace
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Hydraulic Cylinder - Remove and Install - Tilt Cylinder
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Steering Control Support
PM820, PM822, and PM825 Cold Planer Track Pad Bolts - Tighten
C9.3B Aftertreatment Systems SCR Catalyst Inlet Temperature Sensor - Test
C9.3B Aftertreatment Systems DEF Pump Motor - Test
C7.1 Engines and Generator Sets ARD Fuel Pressure Is High
TRS10, TRS14, TRS18, and TRS23 Tilt - Rotator Swivel - Assemble
<B>Wiper Motor Shaft Breakage on Certain K, L, and M Series Medium Wheel Loaders</B> {7305} <B>Wiper Motor Shaft Breakage on Certain K, L, and M Series Medium Wheel Loaders</B> {7305}
730C2 and 725C2 Articulated Truck Power Train Transfer Case - Remove and Install - Center Axle
730C2 and 725C2 Articulated Truck Power Train Transfer Case - Disassemble - Center Axle
349F and 352F Excavator Machine System Service Tools
349F and 352F Excavator Machine System Diagnostic Capabilities
PM820, PM822, and PM825 Cold Planer Machine Systems Gear Motor - Remove and Install - Ventilation
G3500H Generator Set Engine Coolant Pressure Is High
G3500H Generator Set Engine Coolant Temperature Is Low
G3500H Generator Set Engine Detonation Occurrence
PM820, PM822, and PM825 Cold Planer Machine Systems Wear Plate (Rotor Chamber) - Remove and Install