Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
- Disconnect harness assembly (1) from absolute pressure sensor (2).
- Remove absolute pressure sensor (2) from the sensor manifold.
- Disconnect harness assembly (5) from differential pressure sensor (4).
- Remove bolts (3) and differential pressure sensor (4) from the sensor manifold.
Show/hide table
Illustration 2 g03738700 - Remove O-ring seal (6) from absolute pressure sensor (2). Discard O-ring seal (6).
Show/hide table
Illustration 3 g03738701 - Remove O-ring seals (7) from differential pressure sensor (4). Discard O-ring seals (7).
Show/hide table
| |
| Illustration 1 | g03738697 |
Show/hide table
| NOTICE |
|---|
|
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting. |
- Install absolute pressure sensor (2) and differential pressure sensor (4) in the reverse order of removal.
- Tighten bolts (3) to torque of
22 N·m (195 lb in) . - Tighten absolute sensor (2) to torque of
10 N·m (89 lb in) .
- Tighten bolts (3) to torque of
Caterpillar Information System:
Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153} Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153}
Installation Procedure to Retrofit a 471-1988 Swivel Guard Upgrade Kit on Certain Excavators {7183} Installation Procedure to Retrofit a 471-1988 Swivel Guard Upgrade Kit on Certain Excavators {7183}
Installation Procedure to Retrofit Boom and Stick Lowering Control Valves, and a Stick Cylinder Lines Group on Certain 320D, 320D2, and 323DExcavators{5117, 5453, 5458} Installation Procedure to Retrofit Boom and Stick Lowering Control Valves, and a Stick Cylinder Lines Group on Certain 320D, 320D2, and 323DExcavators{5117, 5453, 5458}
Installation Procedure to Retrofit a Boom Lowering Control Valve and a Stick Lowering Control Valve on Certain 330D, 336D, and 336D2 Excavators {5067, 5117, 5147, 5453, 5811} Installation Procedure to Retrofit a Boom Lowering Control Valve and a Stick Lowering Control Valve on Certain 330D, 336D, and 336D2 Excavators {5067, 5117, 5147, 5453, 5811}
Installation Procedure to Retrofit a 471-1992 Heavy Duty Swivel Guard Upgrade Kit on Certain Excavators {7153} Installation Procedure to Retrofit a 471-1992 Heavy Duty Swivel Guard Upgrade Kit on Certain Excavators {7153}
C4.4 Engines General Information
2014/10/27 A New Improved Bucket is Used on Certain 311D Hydraulic Excavators {6526}
Installation of the 260-7860 Pilot Lines Gp On Certain Hydraulic Excavators{5057, 5059} Installation of the 260-7860 Pilot Lines Gp On Certain Hydraulic Excavators{5057, 5059}
Engine Oil Pressure Switch May Cause Oil Pressure Warnings on Certain E Series Mini Hydraulic Excavators{1408} Engine Oil Pressure Switch May Cause Oil Pressure Warnings on Certain E Series Mini Hydraulic Excavators{1408}
Installation Procedure for the 194-0562 Lines Support Gp {5057, 5057} Installation Procedure for the 194-0562 Lines Support Gp {5057, 5057}
Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159} Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159}
420F2 IT, 420F2 ST, 427F2, 428F2, 430F2 IT, 430F2 ST, 432F2, 434F2 and 444F2 Backhoe Loaders Sensor (Multi-Signal, Analog, Active) - Test
2014/11/14 New EMCP 3.2/3.3 Software Is Now Available For Use On Certain Cat® Products {4490, 7620}
793F Off-Highway Truck Fuel Correction Factor - Set
Installation of the 467-8461 Front Lines Gp on Certain Hydraulic Excavators {5057} Installation of the 467-8461 Front Lines Gp on Certain Hydraulic Excavators {5057}
Installation Procedure for the 467-4033 Hydraulic Kit on Certain Hydraulic Excavators{5057, 5264, 5479} Installation Procedure for the 467-4033 Hydraulic Kit on Certain Hydraulic Excavators{5057, 5264, 5479}
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Engine Starting
349F and 352F Excavators Engine Supplement Diesel Exhaust Fluid Filter - Remove and Install
Commissioning Procedure for the 794 AC, 796 AC, and 798 AC Off-Highway Trucks {1000, 7000, 7961} Commissioning Procedure for the 794 AC, 796 AC, and 798 AC Off-Highway Trucks {1000, 7000, 7961}
2014/10/27 The Standard Cat HYDO Oil Change Interval is Extended on All D2-Series, E-Series, and F-Series Excavators {5095, 7000}
335F CR Excavator C7.1 Engine Supplement Water Temperature Regulator - Remove and Install
2014/12/16 Replacing Stem and Spring in Pressure Control Valves H110 and H115 {5117}
325F L Excavator Additional Messages
325F L Excavator Sound Information and Vibration Information