Gear and Bearing - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 3 |
Start By:
- Remove the upper housing. Refer to Disassembly and Assembly, "Upper Housing - Remove".
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before operating any compartment or disassembling any component containing fluids. After collecting all fluids in suitable containers, dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1). Disconnect hose assembly (2) .
Show/hide table
 | |
| Illustration 1 | g01271048 |
- Attach Tooling (A) to mounting ring (3). Attach a suitable lifting device to Tooling (A). The weight of mounting ring (3) is approximately 66 kg (146 lb). Remove mounting ring (3) .
- Remove seal (4) from mounting ring (3) .
Show/hide table
 | |
| Illustration 2 | g01271052 |
- Remove bolts (5) .
Show/hide table
 | |
| Illustration 3 | g01271054 |
- Attach a suitable lifting device and Tooling (A) to the gear and bearing (6). The weight of the gear and bearing (6) is approximately 108 kg (239 lb). Remove the gear and bearing (6) .
Show/hide table
 | |
| Illustration 4 | g01271056 |
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 3 |
| B | 155-0695 | Compound | 1 |
- Attach a suitable lifting and Tooling (A) to the gear and bearing (6). The weight of the gear and bearing (6) is approximately 108 kg (239 lb). Install the gear and bearing (6) .
Show/hide table
| | |
| Illustration 5 | g01271056 |
- Apply Tooling (B) to bolts (5). Install bolts (5). Tighten bolts (5) to a torque of 270 ± 40 N·m (199 ± 30 lb ft).
Show/hide table
| | |
| Illustration 6 | g01271054 |
- Install seal (4) onto mounting ring (3) .
Show/hide table
| | |
| Illustration 7 | g01271052 |
- Apply Tooling (B) to bolts (1). Attach Tooling (A) to mounting ring (3). Attach a suitable lifting device to Tooling (A). The weight of mounting ring (3) is approximately 66 kg (146 lb). Install mounting ring (3) .
Show/hide table
| | |
| Illustration 8 | g01271048 |
- Connect hose assembly (2). Install bolts (1). Tighten bolts (1) to a torque of 270 ± 40 N·m (199 ± 30 lb ft).
Caterpillar Information System:
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioner Lines
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector Rocker Arm
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Rotator Motor and Manifold - Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Swivel - Assemble
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Hydraulic Rotator - Remove
374F Excavator Machine System Pressure Switch (Refrigerant Pressure Cutoff)
324D and 325D Forest Machines Machine Systems Window Wiper Motor - Remove and Install
323D Excavator Specifications
2006/06/05 Correction to Testing and Adjusting , "Relief Valve (Main) - Test and Adjust (Heavy Lift)" {5069, 5069, 5069}
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C11 and C13 Engines Muffler
324D and 325D Forest Machines Machine Systems Cab - Remove
324D and 325D Forest Machines Machine Systems Pump and Motor (Cab Tilt) - Remove and Install
C11 and C13 Engines Liquid Level Sensor (Water Separator)
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 06
C4.4 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump
2006/10/02 The Operation of the Quick Coupler Valve Is Improved {5491}
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 06
2007/01/22 A New Rod Assembly for the Stick Cylinder Is Available {5458}