Muffler
Show/hide table
图 1 | g03644723 |
Show/hide table
231-2160 消声器和安装件总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 1     | 380-9871 消音器卡箍     | 拧紧至扭矩为 40 ± 5 N·m (30 ± 4 lb ft)。     |
2     | 1     | 388-7016 弯曲螺栓卡箍     | 卡箍组件上的开口绝对不能与喷油器上的槽对齐。 拧紧至扭矩为 47 ± 5 N·m (35 ± 4 lb ft)。     |
3     | 1     | 9N-1941 V 形带卡箍     | 拧紧至扭矩为 8.5 ± 1.0 N·m (75.2 ± 8.9 lb in)。     |
4     | 1     | 250-0832 管     | 装配前,使用 Loctite C5A 铜防咬合剂润滑螺纹和轴承表面。     |
Caterpillar Information System:
2006/11/20 Secondary Cab Door Release Lever {7308}
3176C Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
2006/07/03 Installation of an Additional Isolation Valve Prevents Bucket Cylinder Drift {1329, 5057, 5143}
345C Excavator Tool Control System System 11: Relief Valve (Line) - Test and Adjust - Attachment Control Valve
M313C, M315C, M316C, M318C, M322C and M325C Excavators Air Conditioning and Heating Refrigerant Compressor
345C Excavator Tool Control System System 2: Relief Valve (Line) - Test and Adjust - Attachment Control Valve
345C Excavator Tool Control System System 11: Solenoid Valve (Proportional Reducing) - Calibrate - Negative Flow Control
345C Excavator Tool Control System System 2: Solenoid Valve (Proportional Reducing) - Calibrate - Negative Flow Control
345C Excavator Tool Control System System 11: Default Value of Work Tool Parameters
345C Excavator Tool Control System System 2: Default Value of Work Tool Parameters
325D Material Handler Hydraulic System Relief Valve (Main) - Test and Adjust
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2447 - FMI 05
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
2006/06/05 Correction to Testing and Adjusting , "Relief Valve (Main) - Test and Adjust (Heavy Lift)" {5069, 5069, 5069}
323D Excavator Specifications
324D and 325D Forest Machines Machine Systems Window Wiper Motor - Remove and Install
374F Excavator Machine System Pressure Switch (Refrigerant Pressure Cutoff)
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Hydraulic Rotator - Remove
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Swivel - Assemble
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Rotator Motor and Manifold - Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector Rocker Arm
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioner Lines
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install