Swivel - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 2     |
B     | 129-1948     | Grease     | 1     |
C     | 4C-9507     | Compound     | 1     |
D     | 9S-3263     | Thread Lock Compound     | 1     |
- Install seals (13) into the rotor. Install rings (12) into the rotor. Install seals (11) .
Show/hide table
Illustration 1 | g01269874 |
- Apply Tooling (B) to stator (10). Install Tooling (A) and a suitable lifting device onto rotor (9). Install rotor (9) onto stator (10). The weight of rotor (9) is approximately 23 kg (50 lb).
Show/hide table
Illustration 2 | g01269873 |
Show/hide table
Illustration 3 | g01269838 |
- Install ring (8). Install plate (6). Apply Tooling (C) onto bolts (7). Install bolts (7). Bend the corners of plate (6) onto bolts (7) in order to lock bolts (7) .
Show/hide table
Illustration 4 | g01269837 |
- Install blocks (5). Apply Tooling (D) onto bolts (4). Install bolts (4). Tighten bolts (4) to a torque of 105 ± 20 N·m (77 ± 15 lb ft).
Show/hide table
Illustration 5 | g01269835 |
- Install plate (3). Install adapter (2). Apply Tooling (D) onto bolts (1). install bolts (1) .
Show/hide table
Illustration 6 | g01269833 |
End By: Install the swivel. Refer to Disassembly and Assembly, "Swivel - Install".
Caterpillar Information System:
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Hydraulic Rotator - Remove
374F Excavator Machine System Pressure Switch (Refrigerant Pressure Cutoff)
324D and 325D Forest Machines Machine Systems Window Wiper Motor - Remove and Install
323D Excavator Specifications
2006/06/05 Correction to Testing and Adjusting , "Relief Valve (Main) - Test and Adjust (Heavy Lift)" {5069, 5069, 5069}
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C11 and C13 Engines Muffler
2006/11/20 Secondary Cab Door Release Lever {7308}
3176C Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
2006/07/03 Installation of an Additional Isolation Valve Prevents Bucket Cylinder Drift {1329, 5057, 5143}
345C Excavator Tool Control System System 11: Relief Valve (Line) - Test and Adjust - Attachment Control Valve
M313C, M315C, M316C, M318C, M322C and M325C Excavators Air Conditioning and Heating Refrigerant Compressor
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Rotator Motor and Manifold - Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector Rocker Arm
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioner Lines
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
324D and 325D Forest Machines Machine Systems Cab - Remove
324D and 325D Forest Machines Machine Systems Pump and Motor (Cab Tilt) - Remove and Install
C11 and C13 Engines Liquid Level Sensor (Water Separator)
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 06
C4.4 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump