Fuel Priming Pump - Remove and Install - Electric Fuel Priming Pump
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅 操作和保养手册 , "一般危险信息和高压燃油管路 "以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅 系统操作、测试和调整手册 , "燃油系统部件清洁度 "。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 按照本地法规和要求处置所有油液。 |
注: 为便于安装,在所有软管、软管组件、导线及管组件上做出识别标记。 塞住所有软管组件和管组件。 这将有助于防止液体泄漏和防止污染物进入系统。
- 把供油开关转到 关闭位置。
- 将蓄电池断路开关转到 断开位置。
Show/hide table
图 1 g01269003 典型实例 - 从电动注油泵 (4) 断开线束组件 ( 3)。
- 从电动注油泵 (4) 断开塑料管组件 ( 1) 和塑料管组件 (2).。
注: 如果管组件有快插接头,请确保在管组件和燃油注油泵插入之前,接头是清洁的。
- 从电动注油泵 (4) 上卸下螺栓 ( 5)。
- 从安装支架上卸下电动注油泵 ( 4)。
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅 操作和保养手册 , "一般危险信息和高压燃油管路 "以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅 系统操作、测试和调整手册 , "燃油系统部件清洁度 "。 |
- 确保电动注油泵清洁、无磨损或损坏。 如有必要,更换电动注油泵。
Show/hide table
图 2 g01269003 典型实例 - 在安装支架上安装电动注油泵 ( 4)。 安装螺栓 (5) 至电动注油泵。
- 拧紧螺栓 (5) 至扭矩为
9 N·m (79 lb in) 。 - 从塑料管组件 (1)、塑料管组件 ( 2)和电动注油泵 (4). 上卸下所有塞。 将塑料管组件 ( 1) 和塑料管组件 (2) 连接到电动注油泵 ( 4) 上。
注: 如果管组件有快插接头,请确保接头在管组件连接之前是清洁的。
- 连接线束组件 (3) 至电动注油泵 ( 4) 上。
- 将供油开关置于 接通位置。
- 将蓄电池断路开关转到 接通位置。
- 排出燃油系统中的空气。 请参阅操作和保养手册 , "燃油系统 - 充油"。
Caterpillar Information System:
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 06
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2185 - FMI 03
C11 and C13 Engines Liquid Level Sensor (Water Separator)
324D and 325D Forest Machines Machine Systems Pump and Motor (Cab Tilt) - Remove and Install
324D and 325D Forest Machines Machine Systems Cab - Remove
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioner Lines
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector Rocker Arm
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Gear and Bearing - Remove and Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Rotator Motor and Manifold - Install
VRG-20/2, VRG-25/2 and VRG-30/2 Demolition and Sorting Grapples Swivel - Assemble
2006/10/02 The Operation of the Quick Coupler Valve Is Improved {5491}
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2213 - FMI 06
2007/01/22 A New Rod Assembly for the Stick Cylinder Is Available {5458}
2006/06/26 Hole in the Turbine Housing of the Turbocharger {1052}
2006/06/26 Hole in the Turbine Housing of the Turbocharger {1052}
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2214 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2214 - FMI 05
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2214 - FMI 06
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2543 - FMI 03
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System MID 039 - CID 2543 - FMI 04