Cylinder Liner - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | 1     |
A     | 2P-8260     | Cylinder Liner Installation Group     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply 5P-3975 Rubber Lubricant to the new seal. Install new seal (6) in the machined groove on the cylinder liner.
Show/hide table
Illustration 1 | g00516413 |
- Lubricate the lower portion of the cylinder liner with clean engine oil. Ensure that the corresponding crankshaft throw is at bottom center. Position the cylinder liner and guide the connecting rod in place. Use Tool (B) to press the cylinder liner in place.
Note: Refer to the Testing and Adjusting, "Cylinder Liner Projection" topic in order to check the cylinder liner projection.
Note: The word "FRONT" may be stamped on the crown of the pistons in some engines. Ensure that the word "FRONT" is toward the front of the engine when the piston is installed. The etched number on the connecting rod must be on the right side of the engine in the corresponding cylinder.
- Install the upper half of connecting rod bearing (1) in connecting rod (3). Ensure that the bearing tab engages with the slot in the connecting rod. Lubricate the bearing surface with clean engine oil. Tap the piston with a soft hammer until the connecting rod bearing makes contact with the crankshaft.
Show/hide table
Illustration 2 | g00474523 |
- Install connecting rod cap (4). Lubricate connecting rod cap bolts (2) with 4C-5593 Anti-Seize Compound. Install connecting rod cap bolts (2) .
- Tighten the bolts to a torque of 130 ± 7 N·m (95 ± 5 lb ft).
- Place an index mark on each bolt head. Tighten each bolt for an additional 60 ± 5 degrees (1/6 turn).
End By:
- Install the piston cooling jets.
- Install the cylinder head.
Caterpillar Information System:
3500B and 3500B High Displacement Generator Set Engines Electronic Control Terms
3176C and 3196 Marine Engines Cylinder Liner - Remove
Product Link 151/201 System Overview
3408E and 3412E Engines for Caterpillar Built Machines Engine Design
3176C and 3196 Marine Engines Crankshaft Main Bearings - Install
3176C and 3196 Marine Engines Crankshaft Main Bearings - Remove
2000/02/01 Electronic Marine Engine Installation Guides are now Available {1000, 7451}
2000/02/01 114-2410 Pyrometer Battery Shelf Life Extended {7466}
3176C and 3196 Marine Engines Crankshaft - Install
3176C and 3196 Marine Engines Crankshaft - Remove
3176C and 3196 Marine Engines Crankshaft Gear - Remove and Install
3512B Petroleum Engines Aftercooler Coolant Temperature
3176C and 3196 Marine Engines Crankshaft Front Seal - Remove
3176C and 3196 Marine Engines Crankshaft Front Seal - Install
3176C and 3196 Marine Engines Crankshaft Rear Seal - Remove
2000/02/01 Correction to Specifications Module, SENR6436-00, "3114 & 3116 Diesel Truck Engines" {1201}
3176C and 3196 Marine Engines Crankshaft Rear Seal - Install
3176C and 3196 Marine Engines Speed/Timing Sensor - Remove and Install
3176C and 3196 Marine Engines Rocker Shaft and Pushrod - Install
C-12 Marine Engines Cylinder Head - Install
3408E and 3412E Industrial Engines Valve Rocker Arms and Lifters
3176C and 3196 Marine Engines Electric Starting Motor - Remove and Install
3176C and 3196 Marine Engines Engine Oil Filter Base - Remove
2000/05/01 New Format of PC Software for Customer Communication Module {1926}