Mounting Bracket - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1856     | Retaining Ring Pliers As     | 1     |
- Use a suitable lifting device to support the auger drive. The weight of the auger drive is approximately 161 kg (355 lb).
Show/hide table
Illustration 1 | g00684202 |
- Use Tooling (A) in order to remove the retaining ring.
Show/hide table
Illustration 2 | g00685565 |
- Remove pin (2) .
- Remove auger drive (3) from mounting bracket (1). The weight of the auger drive is approximately 161 kg (355 lb).
- Use Tooling (A) in order to remove the retaining ring.
Show/hide table
Illustration 3 | g00684233 |
- Remove pin (5) .
- Remove housing bracket (4) .
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1856     | Retaining Ring Pliers As     | 1     |
- Install housing bracket (4) .
Show/hide table
Illustration 4 | g00684233 |
- Install pin (5) .
- Use Tooling (A) in order to install the retaining ring.
- Use a suitable lifting device in order to align auger drive (3) with mounting bracket (1). The weight of auger drive (3) is approximately 161 kg (355 lb).
Show/hide table
Illustration 5 | g00685565 |
- Install auger drive (3) .
- Install pin (2) .
- Use Tooling (A) in order to install the retaining ring.
Caterpillar Information System:
325C Forest Machines Machine Systems Swing Drive - Remove
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Shutoff and Drain Control
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
307C Excavator Lifting Capacities
A19B and A26B Augers Auger Planetary - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
A19B and A26B Augers Auger Planetary - Disassemble
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
A19B and A26B Augers Gerotor Motor - Install
A19B and A26B Augers Gerotor Motor - Remove
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Water and Sediment - Drain
2004/02/16 Track Roller Groups (Heavy Duty) are Available {4180}
2003/12/29 A New Torque Specification Is Now Used For The Fitting Assembly In The Pilot Lines Group {5057, 5059}
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install - If Equipped
M325D and M330D Excavators Power Train Electronic Control System General Information
325C Material Handler Maintenance Interval Schedule
311C-330C, 345B Series II, 365B and 385B Excavators Stopping the Engine
M325C Excavator Machine System Fuel Tank
325C Forest Machines Machine Systems Swing Drive - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove