Auger Planetary - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 2     |
B     | 6V-4041     | Spanner Wrench As     | 1     |
C     | 1P-0510     | Driver Gp     | 1     |
Start By:
- Remove the gerotor motor. Refer to Disassembly and Assembly, "Gerotor Motor - Remove".
- Remove bolts (1) .
Show/hide table
Illustration 1 | g01044012 |
- Remove cover plate (2) from ring gear (3) .
- Remove thrust washer (4), spline (5), sun gear (6), and two planetary gears (7) .
Show/hide table
Illustration 2 | g01044014 |
- Attach Tooling (A) .
Show/hide table
Illustration 3 | g01045610 |
- Attach a suitable lifting device to Tooling (A) .
- Remove bolts (8) .
Show/hide table
Illustration 4 | g01044015 |
- Remove hub (9) from ring gear (3). The weight of hub (9) is approximately 68 kg (150 lb).
- Bend the tab on lockwasher (11) .
Show/hide table
Illustration 5 | g01044016 |
- Use Tooling (B) in order to remove spanner nut (10) .
- Remove lockwasher (11) and washer (12) .
- Use Tooling (C) in order to remove shaft (13) .
Show/hide table
Illustration 6 | g01044018 |
- Remove bearing cone (14) .
- Remove seal (15) .
Show/hide table
Illustration 7 | g01044019 |
- Remove bearing cone (17) and bearing cup (16) .
Caterpillar Information System:
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
A19B and A26B Augers Gerotor Motor - Install
A19B and A26B Augers Gerotor Motor - Remove
A19B and A26B Augers Auger Planetary and Gerotor Motor - Install
A19B and A26B Augers Auger Planetary and Gerotor Motor - Remove
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Window (Front) - Later Type (If Equipped)
302.5 Mini Hydraulic Excavator Engine Starting
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Assemble
C15 and C18 Engines for Caterpillar Built Machines Turbocharger - Disassemble
5110B Excavator Maintenance Interval Schedule
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
A19B and A26B Augers Auger Planetary - Assemble
307C Excavator Lifting Capacities
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Shutoff and Drain Control
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
325C Forest Machines Machine Systems Swing Drive - Remove
A19B and A26B Augers Mounting Bracket - Remove and Install
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Water and Sediment - Drain
2004/02/16 Track Roller Groups (Heavy Duty) are Available {4180}