Rear Power Take-Off (RPTO) - Install - If Equipped
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0520 | 冲头总成 | 1 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (A) 将套筒轴承 (12) 安装到飞轮壳体中。 套筒轴承上的裂缝位置应保持角度 (Y)，即距竖直中心线 15 ± 1 度。 轴承应安装至深度 (Z)，即
2.0 ± 0.5 mm (0.08 ± 0.02 inch) 。 - 将盖 (10) 和螺栓安装在飞轮壳体的背面。
Show/hide table
图 2 g01134279 - 使用工具 (A) 将套筒轴承 (11) 安装到飞轮壳体中。 套筒轴承上的裂缝位置应保持角度 (X)，即距竖直中心线 15 ± 1 度。 轴承应安装至深度 (Z)，即
2.0 ± 0.5 mm (0.08 ± 0.02 inch) 。 - 将盖 (9) 和螺栓安装在飞轮壳体的背面。
Show/hide table
图 3 g01134263 - 使用工具 (A) 将套筒轴承 (8) 安装到接头 (2) 中。 将 O 形密封圈安装在接头上。
Show/hide table
图 4 g01134262 - 将齿轮组件 (6) 和齿轮组件 (7) 安置在飞轮壳体中。
Show/hide table
图 5 g01115921 - 安置惰齿轮 (5) 和护圈组件 (4)。 安装螺栓 (3)。 拧紧螺栓 (3) 至扭矩为
100 ± 20 N·m (74 ± 15 lb ft) 。 - 使用清洁的发动机机油润滑接头上的 O 形密封圈。 将接头 (2) 安置在飞轮壳体上，安装螺栓 (1)。
Show/hide table
| |
| 图 1 | g01134277 |
结束:
- 安装飞轮。 请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
2003/12/29 A New Torque Specification Is Now Used For The Fitting Assembly In The Pilot Lines Group {5057, 5059}
2004/02/16 Track Roller Groups (Heavy Duty) are Available {4180}
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Water and Sediment - Drain
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
A19B and A26B Augers Mounting Bracket - Remove and Install
325C Forest Machines Machine Systems Swing Drive - Remove
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Shutoff and Drain Control
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
307C Excavator Lifting Capacities
M325D and M330D Excavators Power Train Electronic Control System General Information
325C Material Handler Maintenance Interval Schedule
311C-330C, 345B Series II, 365B and 385B Excavators Stopping the Engine
M325C Excavator Machine System Fuel Tank
325C Forest Machines Machine Systems Swing Drive - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Install
2003/12/29 A New Seal Improves Durability {3282, 3282, 7555}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Equipped with Rear Power Take-Off
325C Forest Machines Machine Systems Swing Drive - Assemble
2003/12/29 A New Welding Process Improves The Tube Assembly In The Pump Lines {5057}