A New Torque Specification Is Now Used For The Fitting Assembly In The Pilot Lines Group {5057, 5059}
- Excavator:
- 345B Series II (S/N: CCC1-UP; DET1-UP)
- 345B Series II L (S/N: CDJ1-UP)
- 345B L (S/N: BFG1-UP; 2SW1-UP)
- 345B (S/N: 7KS1-UP)
- 365B Series II L (S/N: JMB1-UP; PEG1-UP; DER1-UP)
- 365B L (S/N: CTY1-UP; 9TZ1-UP)
- 365B (S/N: 9PZ1-UP)
- 385B (S/N: MYA1-UP; CLS1-UP)
- 385B L (S/N: RCD1-UP; FDL1-UP)
- 5090B (S/N: CLD1-UP; SJY1-UP)
Description of Change: The 164-5567 Fitting Assembly in the pilot lines group is now installed with a new torque specification. The previous torque value for the fitting assembly may cause possible leaking from the back side of the fitting. See illustration 1 for more information.
Adaptable To: Refer to table 1 for the machine effectivity that uses the new torque specification.
Show/hide table
Machine Effectivity     | |||
Model     | S/N Prefix     | Adaptable to:     | Effective with:     |
345B Series II     | S/N:CCC     |
1 - 970     | 971 - Up     |
S/N:DET |
-     | 1 - Up     | |
345B Series II L     | S/N:CDJ     |
-     | 1 - Up     |
345B L     | S/N:BFG     |
-     | 1 - Up     |
S/N:2SW |
-     | 1 - Up     | |
345B     | S/N:7KS     |
-     | 1 - Up     |
365B Series II L     | S/N:JMB     |
1 - 444     | 445 - Up     |
S/N:PEG |
-     | 1 - Up     | |
S/N:DER |
1 - 176     | 177 - Up     | |
365B L     | S/N:CTY     |
-     | 1 - Up     |
S/N:9TZ |
-     | 1 - Up     | |
365B     | S/N:9PZ     |
-     | 1 - Up     |
385B L     | S/N:RCD     |
1 - 167     | 168 - Up     |
S/N:FDL |
1 - 228     | 229 - Up     | |
385B     | S/N:MYA     |
-     | 1 - Up     |
S/N:CLS |
1 - 250     | 251 - Up     | |
5090B     | S/N:CLD     |
1 - 347     | 348 - Up     |
S/N:SJY |
-     | 1 - Up     |
Show/hide table
Illustration 1 | g01044582 |
(1) Torque for the 164-5567 Fitting Assembly ... 55 ± 5 N·m (41 ± 4 lb ft)
Caterpillar Information System:
2004/02/16 Track Roller Groups (Heavy Duty) are Available {4180}
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Water and Sediment - Drain
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
A19B and A26B Augers Mounting Bracket - Remove and Install
325C Forest Machines Machine Systems Swing Drive - Remove
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
311C-330C, 345B Series II, 365B and 385B Excavators Fuel Tank Shutoff and Drain Control
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
307C Excavator Lifting Capacities
A19B and A26B Augers Auger Planetary - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove - If Equipped
C15 and C18 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install - If Equipped
M325D and M330D Excavators Power Train Electronic Control System General Information
325C Material Handler Maintenance Interval Schedule
311C-330C, 345B Series II, 365B and 385B Excavators Stopping the Engine
M325C Excavator Machine System Fuel Tank
325C Forest Machines Machine Systems Swing Drive - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Install
2003/12/29 A New Seal Improves Durability {3282, 3282, 7555}
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Equipped with Rear Power Take-Off