Main Hydraulic Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-5750     | 发动机支座     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 1P-1862     | 钳     | 1     |
注: 如果发生一个故障,精确地诊断原因可以防止其再次发生。 提供有活塞泵和马达故障分析资料。 请参阅专门出版物, SEBD0641, "分析活塞泵和马达轴向故障"。
注: 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 在大修过程中可以安装旧零件。 提供有活塞泵的再使用和修补资料。 请参阅再使用零件和修补操作指南, SEBF8032, "活塞泵和马达"。 在大修过程中,排除所有可能导致原有故障的状况。
注: 检查 O 形密封圈、密封垫和密封件有无磨损或损坏,并在必要时更换部件。
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果有零件磨损或损坏,更换为新零件。 所有拆解和组装步骤必须在清洁的工作台和清洁的液压装置区域中进行。 请始终盖好并保护清洁的部件。
注: 组装之前先将所有部件涂上一薄层液压油。
组装进出口座
- 安装轴承 (11) 。
Show/hide table
图 1 | g00766353 |
- 安装螺塞 (10) 和 O 形密封圈。
Show/hide table
图 2 | g00766344 |
- 安装 O 形密封圈 (9) 。
Show/hide table
图 3 | g00766340 |
- 安装减压阀 (8) 和螺栓 (7) 。 拧紧螺栓 (7) 至扭矩为 9.8 ± 0.3 N·m (86.73 ± 2.65 lb)。
Show/hide table
图 4 | g00766333 |
- 安装 O 形密封圈和螺塞 (6) 。
Show/hide table
图 5 | g00766259 |
- 安装 O 形密封圈 (5) 、盖 (4) 和螺栓 (3) 。 用 55 ± 10 N·m (41 ± 7 lb ft) 的扭矩拧紧螺栓 (3) 。
- 将配流盘 (2) 安装到进出口座 (1) 。
Show/hide table
图 6 | g00766257 |
组装泵
- 将带有密封盒的密封件 (24) 安装到壳体中。
Show/hide table
图 7 | g00765941 |
- 安装轴承 (23) 。
Show/hide table
图 8 | g00765937 |
- 使用工具 (B) 安装挡圈 (22) 。
- 安装轴承座圈 (21) 。
Show/hide table
图 9 | g00765934 |
- 安装齿轮组件 (20) 和隔套 (19) 。
Show/hide table
图 10 | g00765932 |
- 用定位销固定轴承,并安装轴承 (17) 。 轴承必须安装在拆解时标记的原始位置和方向。
Show/hide table
图 11 | g00765927 |
- 使用工具 (C) 安装挡圈 (18) 。
- 安装托架 (16) 和螺栓 (15) 。 拧紧螺栓 (15) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 12 | g00765910 |
- 使用工具 (B) 安装挡圈 (14) 。
Show/hide table
图 13 | g00765908 |
- 安装斜盘 (13) 前,用定位销固定轴承 (17) 。 安装斜盘 (13) 。
Show/hide table
图 14 | g00995706 |
- 将活塞 (11) 和护圈 (10) 作为一个装置安装到柱塞缸 (12) 中。 确保将部件安装在拆解时标记的原始位置。
Show/hide table
图 15 | g00765912 |
- 将旋转总成 (9) 安装在原始位置。
Show/hide table
图 16 | g00765902 |
- 安装 O 形密封圈 (8) 和 (7) 。
Show/hide table
图 17 | g00765898 |
- 安装进出口座 (6) 和螺栓 (5) 。 拧紧螺栓 (5) 至扭矩为 220 ± 30 N·m (162 ± 22 lb ft)。
Show/hide table
图 18 | g00765897 |
- 将盖总成 (4) 安装在原始位置。 安装螺栓 (3) 。 将螺栓 (3) 上紧到 95 ± 15 N·m (70 ± 11 lb ft)。 对泵总成的另一侧重复此步骤。
Show/hide table
图 19 | g00765887 |
- 安装齿轮泵 (2) 和螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 20 | g00765824 |
- 从工具 (A) 拆卸主液压泵。
Show/hide table
图 21 | g00771785 |
End By:
- 安装泵控制装置。 请参阅 拆解和组装, "泵控制装置 - 安装"。
- 安装主液压泵。 请参阅 拆解和组装, "主液压泵 - 安装"。
Caterpillar Information System:
322C Forest Machine Machine Systems Control Valve (Auxiliary) - Assemble
C9.3 Engine for Caterpillar Built Machines Valve Mechanism Cover
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
308C Excavator Machine Systems Main Control Valve - Install
M318C Excavator Machine Systems Steering Cylinder - Assemble
M318C and M322C Excavators Machine Systems Steering Cylinder - Disassemble
3064 and 3066 Engines for Caterpillar Built Machines Coolant Temperature Switch
2002/08/12 Special Instruction, REHS1386 , "Procedures for Modifying the Demolition and Scrap Shears for Installation of the New Covers" {6344}
320C Excavator Leaving the Machine
M318C and M322C Excavators Engine Supplement Engine Oil Cooler - Remove and Install
308C Excavator Machine Systems Hydraulic Oil Tank - Install
308C Excavator Machine Systems Hydraulic Oil Tank - Remove
320B Excavator Machine System Specifications Bucket Cylinder
308C Excavator Machine Systems Heating and Air Conditioning Unit - Remove
308C Excavator Machine Systems Heating and Air Conditioning Unit - Install
5110B Excavator Operator Controls
312C and 315C Excavators Tool Control System Service Tools
2002/09/09 Proper Installation of Exhaust Manifolds {1059}
3056E Industrial Engine Valve Depth - Inspect
320C Material Handler Additional Messages
322C Forest Machine Machine Systems Pilot Valve (Oil Manifold) - Disassemble - NFC Control Valve
Installation of 226-2409 Quick Coupler Conversion Ar {6129, 7000} Installation of 226-2409 Quick Coupler Conversion Ar {6129, 7000}
322C Forest Machine Machine Systems Pilot Valve (Oil Manifold) - Assemble - NFC Control Valve
2002/08/12 A Summary of Revisions Will Start to Appear In Disassembly And Assembly Revisions {1000, 7000}