Engine Oil Cooler - Remove and Install
Removal Procedure
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant. The cooling system contains approximately 39 L (10 US gal) of coolant.
- Open the hood above the engine.
- Disconnect harness assembly (1) from bracket (2) .
Show/hide table
Illustration 1 | g00910225 |
- Remove bracket (2) .
- Remove nuts (3), clamps (4), and tube assemblies (5) .
Show/hide table
Illustration 2 | g00910226 |
- Remove O-ring seals (6) from tube assemblies (5) .
- Remove the bolt, the spacer, and clips (7) .
Show/hide table
Illustration 3 | g00910227 |
- Disconnect tube assemblies (8) .
- Remove bolts (9) .
Show/hide table
Illustration 4 | g00910228 |
Show/hide table
Illustration 5 | g00910232 |
- Remove cover (10) .
- Remove oil cooler (12) .
- Remove gasket (11) and O-ring seals (13) .
Installation Procedure
- Install gasket (11) and O-ring seals (13) .
Show/hide table
Illustration 6 | g00910232 |
Show/hide table
Illustration 7 | g00910228 |
- Install oil cooler (12) .
- Position cover (10) .
- Install bolts (9) .
- Connect tube assemblies (8) .
Show/hide table
Illustration 8 | g00910227 |
- Install clips (7), the spacer, and the bolt.
- Install O-ring seals (6) into tube assemblies (5) .
Show/hide table
Illustration 9 | g00910226 |
- Position tube assemblies (5) and clamps (4) .
- Install nuts (3) .
- Install bracket (2) .
Show/hide table
Illustration 10 | g00910225 |
- Connect harness assembly (1) onto bracket (2) .
Caterpillar Information System:
308C Excavator Machine Systems Hydraulic Oil Tank - Install
308C Excavator Machine Systems Hydraulic Oil Tank - Remove
320C Material Handler Lifting Capacities
2002/08/12 Revised Special Instruction, REHS1343, "Installation of the Replacement Grease Line" is Available {0645, 0645, 5458, 6501, 6535}
M318C and M322C Excavators Engine Supplement Fan - Remove and Install - Aftercooler
M318C and M322C Excavators Engine Supplement Fan Guard - Remove and Install - Aftercooler
M315C Wheeled Hydraulic Excavator Machine System Stick - 2.6 m (8.53 ft)
2002/08/26 VIMS Service Port Information {7601}
M316C Wheeled Excavator Machine System Stick - 2400 mm (7.9 ft)
2002/10/28 New XT-6 ES Hoses are Available {5057, 5102}
M316C Wheeled Excavator Machine System Stick - 2100 mm (6.9 ft)
320C, 322C and 325C Excavators Tool Control System Switches
320C Excavator Leaving the Machine
2002/08/12 Special Instruction, REHS1386 , "Procedures for Modifying the Demolition and Scrap Shears for Installation of the New Covers" {6344}
3064 and 3066 Engines for Caterpillar Built Machines Coolant Temperature Switch
M318C and M322C Excavators Machine Systems Steering Cylinder - Disassemble
M318C Excavator Machine Systems Steering Cylinder - Assemble
308C Excavator Machine Systems Main Control Valve - Install
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
C9.3 Engine for Caterpillar Built Machines Valve Mechanism Cover
322C Forest Machine Machine Systems Control Valve (Auxiliary) - Assemble
315D, 318D and 319D Excavators Machine Systems Main Hydraulic Pump - Assemble
320B Excavator Machine System Specifications Bucket Cylinder
308C Excavator Machine Systems Heating and Air Conditioning Unit - Remove