Housing (Front) - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. |
- Thoroughly clean the old gasket material from front plate (12). Install a new gasket (13) on front plate (12).
Show/hide table
Illustration 2 g00624732 Typical example - Thoroughly clean the old gasket material from housing (9) and install housing (9) on the two dowel pins.
Show/hide table
Illustration 3 g00624681 Typical example - Install bolts (11) in the housing.
Show/hide table
Illustration 4 g00624658 Typical example - Install bolts (7), nut (8), and nuts (10) on housing (9).
Show/hide table
Illustration 5 g00624568 Typical example - Position strap (6) on the housing and on the cylinder head and install bolts (5).
Show/hide table
Illustration 6 g00624350 Typical example - Position clips (3) and install bolts (4).
Show/hide table
Illustration 7 g00624215 Typical example - Install bolts (2).
Show/hide table
Illustration 8 g00624254 Typical example - Install bolts (1) that fasten the bracket to the housing.
Show/hide table
Illustration 1 | g00624827 |
Typical example |
End By:
- Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Install the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
- Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install".
- Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Install".
- Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Caterpillar Information System:
Caterpillar Monitoring System for Electronic Modular Control Panel General Information
30SI Series and 34SI Series Alternator Alternator
3512B Marine Auxiliary Engines Water Temperature Regulators - Install
3512B Marine Auxiliary Engines Water Temperature Regulators - Remove
3126B Truck Engine Fuel System
3512B Marine Auxiliary Engines Exhaust Manifold - Remove and Install
3512B Marine Auxiliary Engines Exhaust Elbow - Remove and Install
C-9 Engines for Caterpillar Built Machines Piston and Rings
3612 and 3616 Engines Fuel Pressure Control Valve - Disassemble
C-15, C-16 and C-18 Truck Engines Housing (Front) - Remove
On-Highway Engines Electronic PTO Installation and Application Guide Component Installation
3512B Marine Auxiliary Engines Air Inlet Manifold - Remove and Install
3116 On Highway Engines Turbocharger - Remove
3116 On Highway Engines Turbocharger - Install
3512B Marine Auxiliary Engine Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
3003, 3013, 3014 and 3024 Industrial Engines Engine Description
3116 On Highway Engines Exhaust Manifold - Remove and Install
3512B Marine Auxiliary Engines Crankshaft Main Bearings - Install
3512B Marine Auxiliary Engines Camshaft - Remove
3512B Marine Auxiliary Engines Camshaft - Install
3512B Marine Auxiliary Engines Crankshaft - Remove
3512B Marine Auxiliary Engines Crankshaft - Install
C-15, C-16 and C-18 Truck Engines Engine Oil Pan - Remove and Install
3003, 3013, 3014 and 3024 Industrial Engines Fuel Shutoff Solenoid - Remove and Install