Engine Oil Filter Housings - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7575 | 连杆支架 | 2 |
B | 1U-9824 | 放油工具总成 | 1 |
5N-5566 | 软管 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 卸下机油冷却器和机油温度调节器壳体。
注: 图示未显示以下部件: 水温调节器壳体 , 连接该壳体的管路 , 机油冷却器 和 卸下的机油温度调节器壳体 。
Show/hide table图 2 g00608737 - 通过打开排放阀从机油滤清器壳体排放机油。
- 将起重机及扎带连接至支架 ( 1)。
- 卸下十个螺栓 (2)。
- 卸下支架 (1)。
Show/hide table
图 3 g00608743 此图为典型的安装图示。 - 断开电气连接 (3)。
- 拧松卡箍并卸下两个螺栓 ( 6)。
- 断开管 (7)。
- 拆下四条螺栓 (4)。
- 卸下盖 (5) 和垫片。 检查是否磨损或损坏。 必要时,更换密封垫。
- 卸下管 (8)。
Show/hide table
图 4 g00624912 所有 G3600 发动机 都配备机油滤清器换向阀。 - 卸下两个箍紧螺栓 ( 11)。
- 断开电气连接 (12)。
- 卸下八个螺栓 (10)(未显示)。
- 卸下盘 (9)(未显示)。
Show/hide table
图 5 g00608756 此图为典型的安装图示。 - 断开电气连接 (13)。
- 卸下两个管 (14)。
注: 电气连接以及模式的其他变更可能要求在卸下部件之前进行更多的拆卸或断开。
- 将起重机和工具 ( A) 固定至机油滤清器壳体。 机油滤清器壳体的重量约为
224 kg (496 lb) 。注: 将电气线路移开,以便卸下壳体时,为机油滤清器壳体留出间隙。
- 卸下五个螺栓 (16)。
- 卸下机油滤清器壳体 ( 15)。
Show/hide table
图 1 | g00608730 |
机油滤清器的盖已卸下。 |
注: 如有配备, U-9824 排油工具总成用于排出机油滤清器壳体中的机油。 1U-9823 过滤勺用于从滤清器壳体上卸下机油滤清器滤芯。
Caterpillar Information System:
SR500 Generators Generator Start-up Checklist
3126B Truck Engine Engine Oil Pan
C15 Petroleum Generator Set Engines Cooling System - Test
G3612 and G3616 Engines Engine Oil Coolers - Install
G3612 and G3616 Engines Engine Oil Coolers - Remove
G3612 and G3616 Engines Engine Oil Coolers - Assemble
3114, 3116 and 3126 Engines Fuel Quality
3612 and 3616 Engines Engine Oil Coolers - Disassemble
3406E and 3456 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
C15 and C18 Petroleum Generator Sets Engine Operation with Active Diagnostic Codes
3612 and 3616 Engines Engine Oil Coolers - Install
3406E and 3456 Engines for Caterpillar Built Machines Aftercooler - Test
3406E and 3456 Engines for Caterpillar Built Machines Water Pump - Test
3612 and 3616 Engines Aftercooler - Remove - Standard Aftercooler
Generator Set Load Sensor Engine Will Not Operate in Parallel - Troubleshoot
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Main Bearings - Inspect
Generator Set Load Sensor Undesired Speed Decrease with Load Increase - Troubleshoot
Generator Set Load Sensor Erratic Operation of Load Sensor - Troubleshoot
G3612 and G3616 Engines Engine Oil Filter Housings - Install
3612 and 3616 Engines Aftercooler - Install - High Performance Aftercooler
3126B Truck Engine General Information
3126B Truck Engine Glossary of Electronic Control Terms
C15 Petroleum Generator Set Engines Cylinder Liner Projection - Inspect