Aftercooler - Remove - Standard Aftercooler
拆卸步骤
开始:
- 拆下排气歧管。 请参阅拆解和组装, "排气歧管 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 卸下将弯头 (1) 和弯头 (2) 固定在涡轮增压器上的螺栓。 将弯头从管道上卸下。
Show/hide table
图 1 | g00398918 |
- 将垫片从弯头 (1) 和弯头 (2) 上卸下。
- 将管道 (3) 和管道 (4) 从壳体 (5) 上卸下。
Show/hide table
图 2 | g00398919 |
- 将壳体 (5) 、壳体 (6) 和壳体 (7) 从后冷器后壳体上卸下。
Show/hide table
图 3 | g00398921 |
- 卸下将法兰 (8) 固定到位的螺栓。 卸下作为组件的法兰和管 (9) 。
Show/hide table
图 4 | g00398922 |
- 卸下将管 (10) 固定在弯头 (11) 中的螺栓和护圈。
- 卸下将弯头 (11) 固定到位的螺栓和垫片 (12) 。 将弯头从后冷管和管 (10) 上卸下。
- 将管道 (13) 和管道 (14) 从后冷器壳体上卸下。
Show/hide table
图 5 | g00398920 |
- 将 O 形密封圈从管道 (13) 和管道 (14) 上卸下。
- 卸下将管道 (15) 固定在后冷器后壳体上的螺栓。
- 将 O 形密封圈从管道 (15) 上拆下。
- 将适当的起吊设备连接在后冷器前壳体上。 后冷器前壳体的重量约为 236 kg (520 lb)。 将螺栓从后冷器前壳体上卸下。 将后冷器前壳体从缸体上卸下。
Show/hide table
图 6 | g00398923 |
- 将适当的起吊设备连接在后冷器后壳体 (16) 上。 后冷器后壳体 (16) 的重量约为 236 kg (520 lb)。 将螺栓 (17) 从后冷器后壳体上卸下。 将后冷器后壳体从缸体上卸下。
- 将垫片 (18) 从缸体上拆下。
Show/hide table
图 7 | g00398924 |
Caterpillar Information System:
3406E and 3456 Engines for Caterpillar Built Machines Water Pump - Test
G3612 and G3616 Engines Engine Oil Filter Housings - Remove
SR500 Generators Generator Start-up Checklist
3126B Truck Engine Engine Oil Pan
C15 Petroleum Generator Set Engines Cooling System - Test
G3612 and G3616 Engines Engine Oil Coolers - Install
G3612 and G3616 Engines Engine Oil Coolers - Remove
G3612 and G3616 Engines Engine Oil Coolers - Assemble
3114, 3116 and 3126 Engines Fuel Quality
3612 and 3616 Engines Engine Oil Coolers - Disassemble
3406E and 3456 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
C15 and C18 Petroleum Generator Sets Engine Operation with Active Diagnostic Codes
Generator Set Load Sensor Engine Will Not Operate in Parallel - Troubleshoot
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Main Bearings - Inspect
Generator Set Load Sensor Undesired Speed Decrease with Load Increase - Troubleshoot
Generator Set Load Sensor Erratic Operation of Load Sensor - Troubleshoot
G3612 and G3616 Engines Engine Oil Filter Housings - Install
3612 and 3616 Engines Aftercooler - Install - High Performance Aftercooler
3126B Truck Engine General Information
3126B Truck Engine Glossary of Electronic Control Terms
C15 Petroleum Generator Set Engines Cylinder Liner Projection - Inspect
3114, 3116 and 3126 Engines Unit Injector Cranking Rack Position
C15 Petroleum Generator Set Engines Flywheel - Inspect