Engine Oil Filter Housings - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7575 | 连杆支架 | 2 |
B | 1U-9824 | 放油工具总成 | 1 |
5N-5566 | 软管 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 将起重机和工具 (A) 固定至机油滤清器壳体。 机油滤清器壳体的重量约为
224 kg (496 lb) 。Show/hide table图 1 g00608756 此图为典型的安装图示。 - 更换机油滤清器壳体 (15)。
- 更换五个螺栓 (16)。
注: 将电气线路移开,以便更换壳体时为机油滤清器壳体留出一定间隙。
注: 电气连接以及模式的其他变更可能要求在更换部件之前进行更多的拆卸或断开。
- 更换两个管 (14)。
- 断开电气连接 (13)。
Show/hide table
图 2 g00624912 - 更换盘 (9)(未显示)。
- 更换八个螺栓 (10)(未显示)。
- 连接电气连接 (12)。
- 更换两个箍紧螺栓 (11)。
Show/hide table
图 3 g00608743 - 更换管 (8)。
- 更换盖 (5) 和垫片。 检查是否磨损或损坏。 必要时,更换密封垫。
- 更换四个螺栓 (4)。
- 连接管 (7)。
- 更换两个螺栓 (6),然后更换卡箍。
- 连接电气连接 (3)。
Show/hide table
图 4 g00608737 - 更换支架 (1)。
- 更换十个螺栓 (2)。
- 将起重机及扎带连接至支架 (1)。
- 将机油加注至机油滤清器。 关于正确油位,请参阅操作和维护手册。
结束:
- 安装机油冷却器和机油温度调节器壳体。
Caterpillar Information System:
Generator Set Load Sensor Erratic Operation of Load Sensor - Troubleshoot
Generator Set Load Sensor Undesired Speed Decrease with Load Increase - Troubleshoot
3408E and 3412E Engines for Caterpillar Built Machines Main Bearings - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Inspect
Generator Set Load Sensor Engine Will Not Operate in Parallel - Troubleshoot
3612 and 3616 Engines Aftercooler - Remove - Standard Aftercooler
3406E and 3456 Engines for Caterpillar Built Machines Water Pump - Test
G3612 and G3616 Engines Engine Oil Filter Housings - Remove
SR500 Generators Generator Start-up Checklist
3126B Truck Engine Engine Oil Pan
C15 Petroleum Generator Set Engines Cooling System - Test
G3612 and G3616 Engines Engine Oil Coolers - Install
3612 and 3616 Engines Aftercooler - Install - High Performance Aftercooler
3126B Truck Engine General Information
3126B Truck Engine Glossary of Electronic Control Terms
C15 Petroleum Generator Set Engines Cylinder Liner Projection - Inspect
3114, 3116 and 3126 Engines Unit Injector Cranking Rack Position
C15 Petroleum Generator Set Engines Flywheel - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Disassemble
C15 Petroleum Generator Set Engines Piston Ring Groove - Inspect
G3612 and G3616 Engines Engine Oil Filter Housings - Assemble
3406E Generator Set Engines Annunciator Panel - Inspect
3406E and 3456 Engines for Caterpillar Built Machines Control Valve (Compression Brake) - Test
3406E and 3456 Engines for Caterpillar Built Machines Solenoid Valve (Compression Brake) - Test