Heat Exchanger - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 开始任何步骤之前,请释放系统内的压力。
热交换器受压时,不要卸下 OSHA 规定的罩。
- 卸下八个螺母 (1) 。
Show/hide table
图 1 | g00594294 |
- 卸下八个螺母 (2) 。
Show/hide table
图 2 | g00594295 |
- 卸下两个螺栓 (3) 。
Show/hide table
图 3 | g00594297 |
- 卸下螺栓 (5) 。
Show/hide table
图 4 | g00594299 |
- 将扎带和适当的起吊设备连接至热交换器 (4) 上。
- 卸下热交换器 (4) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将扎带和适当的起吊设备连接至热交换器 (4) 上。
Show/hide table
图 5 | g00594299 |
- 安装热交换器 (4) 。
- 安装螺栓 (5) 。
- 安装两个螺栓 (3) 。
Show/hide table
图 6 | g00594297 |
- 安装八个螺母 (2) 。
Show/hide table
图 7 | g00594295 |
- 安装八个螺母 (1) 。
Show/hide table
图 8 | g00594294 |
Caterpillar Information System:
3500B Engines and 3500 Engines with EUI Option System Overview
3126B and 3126E Truck Engines Engine Oil Temperature Sensor
3406E and 3456 Generator Set Engines Engine Oil Cooler - Assemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Shutdown Mode
3500B Engines and 3500 Engines with EUI Option Engine Speed/Timing Sensor
797 Off-Highway Truck Steering System Bearing Cup Cooling and Installation Procedure
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Crankshaft Seals
G3606 and G3608 Engines Accessory Module Frame (Front) - Install
3500B and 3500B High Displacement Generator Set Engines ECM/Personality Module
G3500 Engines Turbocharger - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing and Governor - Remove
3406E and 3456 Generator Set Engines Engine Oil Cooler - Disassemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Service Mode
G3606 and G3608 Engines Magneto Drive - Remove and Install
G3606 and G3608 Engines Stub Shaft - Remove
3126B and 3126E Truck Engines Connecting Rod
3612 and 3616 Engines Flexible Coupling
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Pump - Install - 3003 Engines
G3606 and G3608 Engines Vibration Damper Guard - Remove and Install
3406E and 3456 Generator Set Engines Engine Oil Filter Base - Remove
3176C and 3196 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
3612 and 3616 Engines Accessory Drive
3500B Engines and 3500 Engines with EUI Option Digital Sensor Supply
3406E and 3456 Generator Set Engines Engine Oil Filter Base - Install