Accessory Module Frame (Front) - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将链条和适当的起吊设备连接至机架上。
Show/hide table
图 1 | g00594148 |
- 将机架 (2) 安装在底座上。
- 安装四个螺栓 (1) 和垫圈。
- 安装四个螺栓 (3) 和垫圈。
Show/hide table
图 2 | g00594149 |
- 将扎带和适当的起吊设备连接至管道组件 (5) 。
Show/hide table
图 3 | g00594150 |
- 安装管道组件 (5) 。
- 安装卡箍 (7) 和卡箍 (8) 。
- 安装八个螺栓 (6) 。
- 安装八个螺栓 (4) 。
- 将扎带和适当的起吊设备连接至管道组件 (11) 上。
Show/hide table
图 4 | g00594151 |
- 安装管道组件 (11) 。
- 安装八个螺栓 (10) 。
- 安装八个螺栓 (12) 。
- 连接卡箍 (9) 。
- 安装八个螺栓 (14) 。
Show/hide table
图 5 | g00594152 |
- 安装八个螺栓 (13) 。
- 安装管道 (16) 。
Show/hide table
图 6 | g00594153 |
- 安装卡箍 (17) 。
- 安装卡箍 (15) 。
- 安装膨胀水箱。
- 将膨胀箱加注至合适的水位。 更多信息,请参阅操作和维护手册。
- 打开膨胀箱的外部供水。
Caterpillar Information System:
3500B and 3500B High Displacement Generator Set Engines ECM/Personality Module
G3500 Engines Turbocharger - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Fuel Injection Pump Housing and Governor - Remove
3406E and 3456 Generator Set Engines Engine Oil Cooler - Disassemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Normal Mode
3034 Engine for Caterpillar Built Machines Engine Oil Pump - Install
G3606 and G3608 Engines Accessory Module Frame (Front) - Remove
G3606 and G3608 Engines Crankcase Cover - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Modes Of Operation
3406E and 3456 Generator Set Engines Engine Oil Cooler - Install
G3500 Engines Turbocharger - Disassemble
G3500 Engines Turbocharger - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Crankshaft Seals
797 Off-Highway Truck Steering System Bearing Cup Cooling and Installation Procedure
3500B Engines and 3500 Engines with EUI Option Engine Speed/Timing Sensor
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Shutdown Mode
3406E and 3456 Generator Set Engines Engine Oil Cooler - Assemble
3126B and 3126E Truck Engines Engine Oil Temperature Sensor
3500B Engines and 3500 Engines with EUI Option System Overview
G3606 and G3608 Engines Heat Exchanger - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Service Mode
G3606 and G3608 Engines Magneto Drive - Remove and Install
G3606 and G3608 Engines Stub Shaft - Remove
3126B and 3126E Truck Engines Connecting Rod