Fuel Injection Pump Housing and Governor - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 8S-2264     | 泵轮拆卸器     | 1     |
8B-7560 | 踏脚板     | 1     | |
0T-0513 | 螺栓     | 2     | |
5P-1075 | 硬垫圈     | 2     |
开始:
- 拆卸燃油喷油管。 请参考解体与组装, "燃油喷油管 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g00589938 |
3304B 发动机 |
- 在 3304B 发动机上,拆下机油供油管 (26) 、机油回油管 (25) 和隔热罩 (27) 。 检查回油管 (25) 四周的 O 型密封圈。 如果 O 型密封圈损坏,应更换。 从涡轮增压器顶部拆下密封垫和滤网。
- 拆下六个螺母 (1) 和垫圈,然后拆下盖 (2) 。
注: 如果螺母与固定螺柱一起脱出壳体,将螺母 (1) 与固定螺柱分开。 在固定螺柱上涂覆螺纹密封胶,重新安装固定螺柱到深度 19.0 ± 0.8 mm (0.74 ± 0.03 in)。
注: 下图所示为 3306B 发动机的情况。
Show/hide table
图 2 | g00452289 |
- 拆下中间螺栓 (3) 和隔套 (4) 。
Show/hide table
图 3 | g00452292 |
- 安装中间螺栓 (3) 并保留 6.4 mm (.25 in) 的间隙。 如图所示,安装工具 (A) 。 拧紧螺柱,以便从燃油喷油泵凸轮轴上的锥体上松开燃油泵驱动齿轮。
Show/hide table
图 4 | g00452293 |
- 拆下工具 (A) 和螺栓 (3) 。
- 拆下管组件 (5) 和 (11) 。 断开管组件 (8) 和 (9) 的一端。 断开卡箍 (10) 。 拆下两根螺栓 (7) 和垫圈,然后将滤清器底座 (6) 连同滤清器和密封垫一起拆下。
Show/hide table
图 5 | g00452301 |
- 拆下两根螺栓 (12) 、垫圈以及密封垫。 拆下两根螺栓 (14) 和密封垫。 拆下管组件 (13) 。
Show/hide table
图 6 | g00452302 |
- 使用提升吊索和起重机将燃油喷油泵壳体和调速器固定。
Show/hide table
图 7 | g00452343 |
- 断开电磁阀地线 (15) 。 拆下三个螺母 (16) 。 拆下两根螺栓 (17) 和垫圈。 从发动机上拆卸燃油喷油泵壳体和调速器。 要安全拆卸燃油喷油泵壳体和调速器,需要两名技师或适当的举升设备。 3304B 燃油喷油泵壳体和调速器的重量为 24 kg (53 lb)。 3306B 燃油喷油泵壳体和调速器的重量为 32 kg (70 lb)。
- 从喷油泵壳体和调速器上拆下 O 形密封圈。
Caterpillar Information System:
3406E and 3456 Generator Set Engines Engine Oil Cooler - Disassemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Normal Mode
3034 Engine for Caterpillar Built Machines Engine Oil Pump - Install
G3606 and G3608 Engines Accessory Module Frame (Front) - Remove
G3606 and G3608 Engines Crankcase Cover - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Modes Of Operation
3406E and 3456 Generator Set Engines Engine Oil Cooler - Install
G3500 Engines Turbocharger - Disassemble
G3500 Engines Turbocharger - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Crankshaft
G3612 and G3616 Engines Air/Fuel Pressure Sensor Module - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Customer Parameters Worksheet
G3500 Engines Turbocharger - Assemble
3500B and 3500B High Displacement Generator Set Engines ECM/Personality Module
G3606 and G3608 Engines Accessory Module Frame (Front) - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Crankshaft Seals
797 Off-Highway Truck Steering System Bearing Cup Cooling and Installation Procedure
3500B Engines and 3500 Engines with EUI Option Engine Speed/Timing Sensor
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Shutdown Mode
3406E and 3456 Generator Set Engines Engine Oil Cooler - Assemble
3126B and 3126E Truck Engines Engine Oil Temperature Sensor
3500B Engines and 3500 Engines with EUI Option System Overview
G3606 and G3608 Engines Heat Exchanger - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines Service Mode