Idler Gears (Rear) - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查轴 (7) 是否损坏。 轴 (7) 的轴承表面直径应为 105.84 ± 0.02 mm (4.167 ± 0.001 inch)。 将销安装在轴 (7) 的表面上方 7.0 ± 0.5 mm (0.28 ± 0.02 inch) 处。
Show/hide table
图 1 | g00561146 |
- 将适当的起吊设备连接至轴 (7) 上。 轴 (7) 的重量约为 25 kg (55 lb)。 将轴 (7) 定位在缸体上。 安装螺栓 (9) 。 将螺栓拧紧至扭矩为 270 ± 25 N·m (200 ± 18 lb ft)。
- 安装止推垫圈 (8) 。
- 组装惰轮组件:
- 如有必要,安装轴承 (4) 。 轴承 (4) 必须位于齿轮 (6) 表面下方 2.50 ± 0.5 mm (0.098 ± 0.02 inch) 处。
- 将齿轮 (3) 定位在齿轮 (6) 上。 安装螺栓 (5) 。
Show/hide table
图 2 | g00561145 |
- 将适当的起吊设备连接至惰轮组件 (2) 上。 惰轮组件 (2) 的重量约为 54 kg (119 lb)。 将惰轮组件 (2) 安装在轴上。 安装护圈 (1) 。
Show/hide table
图 3 | g00561144 |
End By: 安装凸轮轴主动齿轮。 请参阅 拆解和组装, "凸轮轴驱动齿轮 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Idler Gears (Rear) - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Full Protection System (OP, WT, OS)
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Switches
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Install
G3606 and G3608 Engines Camshaft Drive Gear - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Transmitters
G3606 and G3608 Engines Camshaft Drive Gear - Remove
G3408 and G3412 Engines Engine Oil Pressure Indicator
G3304 and G3306 Engines Water Temperature Indicator
G3408 and G3412 Engines Ammeter
G3304 and G3306 Engines Overspeed Contactor
G3408 and G3412 Engines Ignition System
G3408 and G3412 Engines Air Inlet and Exhaust System
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3606 and G3608 Engines Idler Gears (Front) - Install
G3606 and G3608 Engines Magnetic Pickup - Remove and Install
G3606 and G3608 Engines Housing (Front) - Remove
Digital Voltage Regulator KVAR Regulation
Digital Voltage Regulator Power Factor Regulation
Digital Voltage Regulator Voltage Regulation
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Assemble
Digital Voltage Regulator Line Loss Compensation
G3606 and G3608 Engines Housing (Front) - Install