Idler Gears (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0510     | 起子总成     | 1     |
B     | 8T-5096     | 千分表     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将止推垫圈 (1) 放在前壳体定位销上的合适位置。 新止推垫圈的厚度为 0.945 ± 0.05 mm (0.0372 ± 0.0020 inch)。
Show/hide table
图 1 | g00561483 |
- 如果已拆下轴承 (2) ,请使用工具 (A) 安装齿轮 (3) 上的轴承。 安装轴承,直到尺寸 (X) 为 2.5 ± 0.5 mm (0.098 ± 0.020 inch)。 安装后的轴承内径应为 69.987 ± 0.040 mm (2.7554 ± 0.0016 inch)。
Show/hide table
图 2 | g00561504 |
典型实例 |
注: 图中的惰轮轴承表示为内部供油的凹槽。 新的惰轮轴承不带内部供油的凹槽。
- 在轴 (4) 上安装 O 形密封圈 (5) 。 在 O 形密封圈上涂抹清洁的发动机机油。
Show/hide table
图 3 | g00561505 |
- 将清洁发动机机油涂在齿轮 (3) 的轴承上。
Show/hide table
图 4 | g00561506 |
注: 每侧的惰齿轮都不同。 必须将齿轮安装在正确的一侧,以便与曲轴齿轮正确接合。
- 将齿轮 (3) 放置在合适位置,并使齿轮的大凸肩位于前方。 安装轴 (4) 。
- 安装将轴 (4) 固定到位的螺栓 (6) 。
- 使用工具 (B) 检查曲轴齿轮与惰轮 (3) 之间的齿隙。 齿隙应为 0.051至 0.533 mm (0.0020 至 0.0209 in)。
Show/hide table
图 5 | g00561589 |
- 使用工具 (B) 检查齿轮 (3) 的端隙。 轴向间隙应为 0.25 至 0.85 mm (0.010 至 0.033 in)。
End By:
- 安装机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
- 安装水泵。 请参阅 拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Idler Gears (Front) - Remove
G3408 and G3412 Engines Air Inlet and Exhaust System
G3408 and G3412 Engines Ignition System
G3606 and G3608 Engines Idler Gears (Rear) - Install
G3606 and G3608 Engines Idler Gears (Rear) - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Disassemble
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Full Protection System (OP, WT, OS)
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Switches
P16, P20, P25, P28, P40 and P60 Pulverizers Rotary Manifold - Install
G3606 and G3608 Engines Camshaft Drive Gear - Install
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Transmitters
G3606 and G3608 Engines Camshaft Drive Gear - Remove
G3606 and G3608 Engines Magnetic Pickup - Remove and Install
G3606 and G3608 Engines Housing (Front) - Remove
Digital Voltage Regulator KVAR Regulation
Digital Voltage Regulator Power Factor Regulation
Digital Voltage Regulator Voltage Regulation
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Assemble
Digital Voltage Regulator Line Loss Compensation
G3606 and G3608 Engines Housing (Front) - Install
Digital Voltage Regulator Reactive Voltage Droop
G3408C and G3412C Engines Lubrication System
Digital Voltage Regulator Cross Current Compensation
PM3412C Power Modules Stopping the Engine